AD7884AN データシートの表示（PDF） - Analog Devices

部品番号

コンポーネント説明

一致するリスト

AD7884AN

LC2MOS 16-Bit, High Speed Sampling ADCs

Analog Devices 

AD7884/AD7885

The required +3 V reference is derived from the AD780 and

buffered by the high-speed amplifier A3 (AD845, AD817 or

equivalent). A4 is a unity gain inverter which provides the –3 V

negative reference. The gain setting resistors are on-chip and

are factory trimmed to ensure precise tracking of VREF+. Figure

6 shows A3 and A4 as AD845s or AD817s. These have the ability

to respond to the rapidly changing reference input impedance.

CIRCUIT DESCRIPTION

Analog Input Section

The analog input section of the AD7884/AD7885 is shown in

Figure 7. It contains both the input signal conditioning and

sample-and-hold amplifier. Note that the analog input is truly

benign. When SW1a goes open circuit to put the SHA into the

hold mode, SW1b is closed. This means that the input resis-

tors, R1 and R2 are always connected to either virtual ground

or true ground.

R3 3kΩ

±3V IN F

±3V IN S

±5VIN F

±5V IN S

R1 3kΩ

C1

SW1a

A1

R2 5kΩ

SW1b

TO RESIDUE

AMPLIFIER A2

R4 4kΩ

R6 2kΩ

TO

9-BIT

ADC

R5 4kΩ

VREF–

Figure 7. AD7884/AD7885 Analog Input Section

When the ± 3 VINS and ± 3 VINF inputs are tied to 0 V, the in-

put section has a gain of –0.6 and transforms an input signal

of ± 5 volts to the required ± 3 volts. When the ± 5 VINS and

± 5 VINF inputs are grounded, the input section has a gain of

–1 and so the analog input range is now ± 3 volts. Resistors R4

and R5, at the amplifier output, further condition the ± 3 volts

signal to be 0 to –3 volts. This is the required input for the 9-bit

A/D converter section.

With SW1a closed, the output of A1 follows the input (the

sample-and-hold is in the track mode). On the rising edge of

the CONVST pulse, SW1a goes open circuit, and capacitor C1

holds the voltage on the output of A1. The sample-and-

hold is now in the hold mode. The aperture delay time for the

sample-and-hold is nominally 50 ns.

A/D Converter Section

The AD7884/AD7885 uses a two-pass flash technique in order

to achieve the required speed and resolution. When the CONVST

control input goes from low to high, the sample-and-hold ampli-

fier goes into the hold mode and a 0 V to –3 V signal is pre-

sented to the input of the 9-bit ADC. The first phase of

conversion generates the 9 MSBs of the 16-bit result and trans-

fers these to the latch and ALU combination. They are also fed

back to the 9 MSBs of the 16-bit DAC. The 7 LSBs of the

DAC are permanently loaded with 0s. The DAC output is sub-

tracted from the analog input with the result being amplified

and offset in the Residue Amplifier Section. The signal at the

output of A2 is proportional to the error between the first phase

result and the actual analog input signal and is digitized in the

second conversion phase. This second phase begins when the

16-bit DAC and the Residue Error Amplifier have both settled.

First, SW2 is turned off and SW3 is turned on. Then, the SHA

section of the Residue Amplifier goes into hold mode. Next

SW2 is turned off and SW3 is turned on. The 9-bit result is

transferred to the output latch and ALU. An error correction al-

gorithm now compensates for the offset inserted in the Residue

Amplifier Section and errors introduced in the first pass conver-

sion and combines both results to give the 16-bit answer.

±3V SIGNAL

FROM INPUT

SHA

R6

2kΩ

R4 4kΩ 0 TO –3V

SW2

R5

4kΩ

V REF–

A2

SW3

RESIDUE AMP

+ SHA

16-BIT

ACCURATE

9

DAC

+3V

–3V

9-BIT

ADC

9

LATCH

+

16

9 ALU

R7

2kΩ

R8

2kΩ

V REF+ F VREF+S VINV V REF–

Figure 8. A/D Converter Section

–8–

REV. C

Share Link: