AD7884AN データシートの表示（PDF） - Analog Devices

部品番号

コンポーネント説明

一致するリスト

AD7884AN

LC2MOS 16-Bit, High Speed Sampling ADCs

Analog Devices 

AD7884/AD7885

If the noise in the converter is too high for an application, it can

be reduced by oversampling and digital filtering. This involves

sampling the input at higher than the required word rate and

then averaging to arrive at the final result. The very fast conver-

sion time of the AD7884/AD7885 makes it very suitable for

oversampling. For example, if the required input bandwidth is

40 kHz, the AD7884/AD7885 could be oversampled by a factor

of 2. This yields a 3 dB improvement in the effective SNR per-

formance. The noise performance in the ± 5 volt input range is

now effectively 85 µV rms and the resultant spread of codes for

2500 conversions will be four. This is shown in Figure 15.

1500

1000

500

16

15

14

13

12

11

10

0

20

40

60

80

FREQUENCY – kHz

Figure 17. Effective Number of Bits vs. Frequency

The effective number of bits for a device can be calculated from

its measured SNR. Figure 17 shows a typical plot of effective

number of bits versus frequency for the AD7884. The sampling

frequency is 166 kHz.

0

(X – 1) (X) (X + 1) (X + 2)

CODE

Figure 15. Histogram of 2500 Conversions of a DC Input

Using a ×2 Oversampling Ratio

Dynamic Performance

With a combined conversion and acquisition time of 6 µs, the

AD7884/AD7885 is ideal for wide bandwidth signal processing

applications. Signal to (Noise + Distortion), Total Harmonic

Distortion, Peak Harmonic or Spurious Noise and Intermodula-

tion Distortion are all specified. Figure 16 shows a typical

FFT plot of a 1.8 kHz, ± 5 V input after being digitized by the

AD7884/AD7885.

0

f IN = 1.8kHz, ± 5V SINE WAVE

fSAMPLE = 163kHz

–30

SNR = 87dB

THD = –95dB

–60

–90

–120

MICROPROCESSOR INTERFACING

The AD7884/AD7885 is designed on a high speed process

which results in very fast interfacing timing (Data Access Time

of 57 ns max). The AD7884 has a full 16-bit parallel bus, and

the AD7885 has an 8-bit wide bus. The AD7884, with its paral-

lel interface, is suited to 16-bit parallel machines whereas the

AD7885, with its byte interface, is suited to 8-bit machines.

Some examples of typical interface configurations follow.

AD7884 to MC68000 Interface

Figure 18 shows a general interface diagram for the MC68000,

16-bit microprocessor to the AD7884. In Figure 18, conversion

is initiated by bringing CSA low (i.e., writing to the appropriate

address). This allows the processor to maintain control over the

complete conversion process. In some cases it may be more

desirable to control conversion independent from the processor.

This can be done by using an external sampling timer.

A23 – A1

ADDRESS BUS

MC68000

DTACK

AS

R/W

D15 – D0

ADDRESS

DECODE LOGIC

CSB CSA

DATA BUS

AD7884

CONVST

CS

RD

DB15 – DB0

–150

2048 POINT FFT

Figure 16. AD7884/AD7885 FFT Plot

Effective Number of Bits

The formula for SNR (see Terminology section) is related to

the resolution or number of bits in the converter. Rewriting the

formula, below, gives a measure of performance expressed in

effective number of bits (N).

N = (SNR – 1.76)/6.02

Figure 18. AD7884 to MC68000 Interface

Once conversion has been started, the processor must wait until

it is completed before reading the result. There are two ways of

ensuring this. The first way is to simply use a software delay to

wait for 6.5 µs before bringing CS and RD low to read the data.

REV. C

–11–

Share Link: