PCF8576DU/2DA/2 データシートの表示（PDF） - Philips Electronics

部品番号

コンポーネント説明

一致するリスト

PCF8576DU/2DA/2

Universal LCD driver for low multiplex rates

Philips Electronics 

Philips Semiconductors

Universal LCD driver for low

multiplex rates

Product specification

PCF8576D

7 CHARACTERISTICS OF THE I2C-BUS

The I2C-bus is for bidirectional, two-line communication

between different ICs or modules. The two lines are a

serial data line (SDA) and a serial clock line (SCL). Both

lines must be connected to a positive supply via a pull-up

resistor when connected to the output stages of a device.

Data transfer may be initiated only when the bus is not

busy.

In chip-on-glass applications where the track resistance

from the SDA pad to the system SDA line can be

significant, a potential divider is generated by the bus

pull-up resistor and the Indium Tin Oxide (ITO) track

resistance. It is therefore necessary to minimize the track

resistance from the SDA pad to the system SDA line to

guarantee a valid LOW-level during the acknowledge

cycle.

7.1 Bit transfer

One data bit is transferred during each clock pulse. The

data on the SDA line must remain stable during the HIGH

period of the clock pulse as changes in the data line at this

time will be interpreted as a control signal (see Fig.13).

7.2 Start and stop conditions

Both data and clock lines remain HIGH when the bus is not

busy. A HIGH-to-LOW transition of the data line while the

clock is HIGH is defined as the START condition (S).

A LOW-to-HIGH transition of the data line while the clock

is HIGH is defined as the STOP condition (P), (see Fig.14).

7.3 System configuration

A device generating a message is a ‘transmitter’, a device

receiving a message is the ‘receiver’. The device that

controls the message is the ‘master’ and the devices which

are controlled by the master are the ‘slaves’, (see Fig.15).

7.4 Acknowledge

The number of data bytes that can be transferred from

transmitter to receiver between the START and STOP

conditions is unlimited. Each byte of eight bits is followed

by an acknowledge bit. The acknowledge bit is a

HIGH-level signal on the bus that is asserted by the

transmitter during which time the master generates an

extra acknowledge related clock pulse. An addressed

slave receiver must generate an acknowledge after

receiving each byte. Also a master receiver must generate

an acknowledge after receiving each byte that has been

clocked out of the slave transmitter. The acknowledging

device must pull-down the SDA line during the

acknowledge clock pulse so that the SDA line is stable

LOW during the HIGH period of the acknowledge related

clock pulse (set-up and hold times must be taken into

consideration). A master receiver must signal an end of

data to the transmitter by not generating an acknowledge

on the last byte that has been clocked out of the slave.

In this event the transmitter must leave the data line HIGH

to enable the master to generate a STOP condition (see

Fig.16).

7.5 PCF8576D I2C-bus controller

The PCF8576D acts as an I2C-bus slave receiver. It does

not initiate I2C-bus transfers or transmit data to an I2C-bus

master receiver. The only data output from the PCF8576D

are the acknowledge signals of the selected devices.

Device selection depends on the I2C-bus slave address,

on the transferred command data and on the hardware

subaddress.

In single device applications, the hardware subaddress

inputs A0, A1 and A2 are normally tied to VSS which

defines the hardware subaddress 0. In multiple device

applications A0, A1 and A2 are tied to VSS or VDD in

accordance with a binary coding scheme such that no two

devices with a common I2C-bus slave address have the

same hardware subaddress.

7.6 Input filters

To enhance noise immunity in electrically adverse

environments, RC low-pass filters are provided on the

SDA and SCL lines.

7.7 I2C-bus protocol

Two I2C-bus slave addresses (01110000 and 01110010)

are reserved for the PCF8576D. The least significant bit of

the slave address that a PCF8576D will respond to is

defined by the level tied to its SA0 input. The PCF8576D

is a write-only device and will not respond to a read

access. Having two reserved slave addresses allows the

following on the same I2C-bus:

• Up to 16 PCF8576Ds for very large LCD applications

• The use of two types of LCD multiplex drive.

The I2C-bus protocol is shown in Fig.17. The sequence is

initiated with a START condition (S) from the I2C-bus

master which is followed by one of two possible

PCF8576D slave addresses available. All PCF8576Ds

whose SA0 inputs correspond to bit 0 of the slave address

respond by asserting an acknowledge in parallel. This

I2C-bus transfer is ignored by all PCF8576Ds whose SA0

inputs are set to the alternative level.

2004 Dec 22

20

Share Link: