PCF8576DU/2DA/2 データシートの表示（PDF） - Philips Electronics

部品番号

コンポーネント説明

一致するリスト

PCF8576DU/2DA/2

Universal LCD driver for low multiplex rates

Philips Electronics 

Philips Semiconductors

Universal LCD driver for low

multiplex rates

Product specification

PCF8576D

In the 1 : 4 mode, the eight transmitted data bits are

placed in bits 0, 1, 2 and 3 of two successive display RAM

addresses.

6.11 Data pointer

The addressing mechanism for the display RAM is

realized using the data pointer. This allows the loading of

an individual display data byte, or a series of display data

bytes, into any location of the display RAM. The sequence

commences with the initialization of the data pointer by the

LOAD DATA POINTER command. Following this, an

arriving data byte is stored at the display RAM address

indicated by the data pointer in accordance with the filling

order shown in Fig.12. After each byte is stored, the

contents of the data pointer are automatically incremented

by a value dependent on the selected LCD drive mode:

eight (static drive mode), four (1 : 2 mode), three

(1 : 3 mode) or two (1 : 4 mode). If an I2C-bus data access

is terminated early then the state of the data pointer will be

unknown. The data pointer should be re-written prior to

further RAM accesses.

display RAM addresses (rows) / segment outputs (S)

01234

35 36 37 38 39

0

display RAM bits

(columns) /

1

backplane outputs

(BP)

2

3

MBE525

Fig.11 Display RAM bit-map showing direct relationship between display RAM addresses and segment outputs,

and between bits in a RAM word and backplane outputs.

6.12 Subaddress counter

The storage of display data is determined by the contents

of the subaddress counter. Storage is allowed to take

place only when the contents of the subaddress counter

agree with the hardware subaddress applied to A0, A1

and A2. The subaddress counter value is defined by the

DEVICE SELECT command. If the contents of the

subaddress counter and the hardware subaddress do not

agree then data storage is inhibited but the data pointer is

incremented as if data storage had taken place. The

subaddress counter is also incremented when the data

pointer overflows.

The storage arrangements described lead to extremely

efficient data loading in cascaded applications. When a

series of display bytes are sent to the display RAM,

automatic wrap-over to the next PCF8576D occurs when

the last RAM address is exceeded. Subaddressing across

device boundaries is successful even if the change to the

next device in the cascade occurs within a transmitted

character (such as during the 14th display data byte

transmitted in 1 : 3 mode).

The hardware subaddress should not be changed whilst

the device is being accessed on the I2C-bus interface.

6.13 Output bank selector

The output bank selector selects one of the four bits per

display RAM address for transfer to the display latch. The

actual bit chosen depends on the selected LCD drive

mode and on the instant in the multiplex sequence. In 1 : 4

mode, all RAM addresses of bit 0 are selected, these are

followed by the contents of bit 1, bit 2 and then bit 3.

Similarly in 1 : 3 mode, bits 0, 1 and 2 are selected

sequentially. In 1 : 2 mode, bits 0 and 1 are selected and,

in static mode, bit 0 is selected. Signal SYNC will reset

these sequences to the following starting points; bit 3 for

1 : 4 mode, bit 2 for 1 : 3 mode, bit 1 for 1 : 2 mode and

bit 0 for static mode.

The PCF8576D includes a RAM bank switching feature in

the static and 1 : 2 drive modes. In the static drive mode,

the BANK SELECT command may request the contents of

bit 2 to be selected for display instead of the contents of

bit 0. In 1 : 2 mode, the contents of bits 2 and 3 may be

selected instead of bits 0 and 1. This allows display

information to be prepared in an alternative bank and then

selected for display when it is assembled.

2004 Dec 22

17

Share Link: