10XS4200 データシートの表示（PDF） - Freescale Semiconductor
部品番号
コンポーネント説明
一致するリスト
10XS4200 Datasheet PDF : 60 Pages
| |||
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics
Unless specified otherwise: 8.0 V ≤ VPWR ≤ 36 V, 3.0 V ≤ VDD ≤ 5.5 V, - 40 °C ≤ TA ≤ 125 °C, GND = 0 V. Typical values are
average values evaluated under nominal conditions TA = 25 °C, VPWR = 28 V & VDD = 5.0 V, unless specified otherwise.
parameter
Symbol
Min
Typ
Max
Unit
SUPPLY ELECTRICAL CHARACTERISTICS
Supply Voltage Range:
Full Specification compliant
Extended Mode(10)
VPWR
8.0
24
36
V
6.0
–
58
VPWR Supply Current, device in wake-up mode, channel On, Open-load
IPWR(ON)
mA
outputs in ON-state, HS[0 : 1] open, IN[0:1] > VIH
–
6.5
8.0
VPWR Supply Current, device in wake-up mode (Standby), channel Off
IPWR(SBY)
Open-load in OFF-state Detection Disabled, HS[0 : 1] shorted to ground
–
with VDD = 5.5 V and RSTB > VWAKE
Sleep State Supply Current
VPWR = 24 V, RSTB = IN[0:1] < VWAKE, HS[0 : 1] connected to ground
IPWR(SLEEP)
TA = 25 °C
–
TA = 125 °C
–
mA
6.5
8.0
μA
3.0
10.0
–
60.0
VDD Supply Voltage
VDD Supply Current at VDD = 5.5 V
No SPI Communication
8.0 MHz SPI Communication(11)
VDD(ON)
3.0
–
5.5
V
IDD(ON)
mA
–
–
2.2
–
5.0
–
VDD Sleep State Current at VDD = 5.5 V with or without VPWR
IDD(SLEEP)
–
–
5.0
μA
Over-voltage Shutdown Threshold
VPWR(OV)
39
42
45.5
V
Over-voltage Shutdown Hysteresis
VPWR(OVHYS)
0.2
0.8
1.5
V
Under-voltage Shutdown Threshold(12)
VPWR(UV)
5.0
–
6.0
V
VPWR Power-On-Reset (POR) Voltage Threshold(12)
VPWR(POR)
2.2
2.6
4.0
V
VDD Power-On-Reset (POR) Voltage Threshold(12)
VDD(POR)
1.5
2.0
2.5
V
VDD Supply Failure Voltage Threshold (assumed VPWR > VPWR(UV))
VDD(FAIL)
2.2
2.5
2.8
V
Notes
10. In extended mode, several device functions (channel control, RDS(ON) and over-temperature protection) are guaranteed, but compliance
with the specified values in this document is not. Below 6.0 V, the device is only protected from overheating (thermal shutdown). Above
VPWR(OV), the channels can only be turned ON when the over-voltage detection function has been disabled.
11. Typical value guaranteed per design.
12. When the device recovers from under-voltage and returns to normal mode (6.0 V < VPWR < 58 V) before the end of the auto-retry period
(see Auto-retry), the device will perform normally. When VPWR drops below VPWR(UV), under-voltage is detected see Under-voltage
Fault (Latchable Fault) and EMC Performances.
10XS4200
8
Analog Integrated Circuit Device Data
Freescale Semiconductor
Share Link: 