ADG528A データシートの表示（PDF） - Analog Devices
部品番号
コンポーネント説明
一致するリスト
ADG528A Datasheet PDF : 12 Pages
| |||
ADG528A/ADG529A
TERMINOLOGY
RON
RON Match
RON Drift
IS (OFF)
Ohmic resistance between terminals D and S
Difference between the RON of any two channels
Change in RON versus temperature
Source terminal leakage current when the switch
is off.
ID (OFF) Drain terminal leakage current when the switch is
off.
ID (ON)
Leakage current that flows from the closed switch
into the body.
VS (VD)
CS (OFF)
CD (OFF)
CIN
tON (EN)
Analog voltage on terminal S or D
Channel input capacitance for “OFF” condition
Channel output capacitance for “OFF” condition
Digital input capacitance
Delay time between the 50% and 90% points of
the digital input and switch “ON” condition.
tOFF (EN)
tTRANSITION
tOPEN
VINL
VINH
IINL (IINH)
VDD
VSS
IDD
ISS
Delay time between the 50% and 10% points of
the digital input and switch “OFF” condition
Delay time between the 50% and 90% points of
the digital inputs and switch “ON” condition
when switching from one address state to another.
“OFF” time measured between 50% points of
both switches when switching from one address
state to another
Maximum input voltage for Logic “0”
Minimum input voltage for Logic “1”
Input current of the digital input
Most positive voltage supply
Most negative voltage supply
Positive supply current
Negative supply current
OUTLINE DIMENSIONS
18-Lead Plastic Dual In-Line Package [PDIP]
(N-18)
Dimensions shown in inches and (millimeters)
0.180 (4.57)
MAX
0.885 (22.48)
0.845 (21.46)
18
10
1
9
0.015 (0.38) MIN
0.295 (7.49)
0.275 (6.99)
0.325 (8.26)
0.300 (7.62)
0.180 (4.57)
MAX
0.150 (3.81)
0.110 (2.79)
0.022 (0.558)
0.014 (0.356)
SEATING
0.100 0.060 (1.52) PLANE
(2.54)
BSC
0.045
(1.14)
0.015 (0.381)
0.008 (0.203)
COMPLIANT TO JEDEC STANDARDS MO-095AD
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
20-Lead Plastic Leaded Chip Carrier [PLCC]
(P-20A)
Dimensions shown in inches and (millimeters)
0.048 (1.21)
0.042 (1.07)
0.056 (1.42)
0.042 (1.07)
0.048 (1.21)
0.042 (1.07)
0.020
(0.50)
R
3
4
19
18
TOP VIEW
(PINS DOWN)
8
9
14
13
0.356 (9.04)
0.350 (8.89) SQ
0.050
(1.27)
BSC
0.395 (10.02)
0.385 (9.78) SQ
0.180 (4.57)
0.165 (4.19)
0.20 (0.51)
MIN
0.020 (0.50)
R
0.021 (0.53)
0.013 (0.33)
0.330 (8.38)
0.032 (0.81) 0.290 (7.37)
0.026 (0.66)
0.120 (3.04)
0.090 (2.29)
0.040
0.025
(1.01)
(0.64)
R
BOTTOM
VIEW
(PINS UP)
COMPLIANT TO JEDEC STANDARDS MO-047AA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
–10–
REV. B
Share Link: 