MC100EL56(2016) データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
一致するリスト
MC100EL56 Datasheet PDF : 6 Pages
| |||
MC100EL56
Table 6. 100EL SERIES NECL DC CHARACTERISTICS (VCC = 0.0 V; VEE = −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
IIH
IIL
Power Supply Current
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single-Ended)
Input LOW Voltage (Single-Ended)
Output Voltage Reference
Common Mode Range
(Differential Configuration) (Note 3)
VPP t 500 mV
VPP ≥ 500 mV
Input HIGH Current
Input LOW Current
20
24
20
24
20
24 mA
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
−1165
−880 −1165
−880 −1165
−880 mV
−1810
−1475 −1810
−1475 −1810
−1475 mV
−1.38
−1.26 −1.38
−1.26 −1.38
−1.26 V
V
−3.7
−0.4 −3.8
−3.5
−0.4 −3.6
150
0.5
0.5
−0.4 −3.8
−0.4 −3.6
150
0.5
−0.4
−0.4
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
2. Outputs are terminated through a 50ĂW resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin
and 1 V.
Table 7. AC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
fmax
tPLH
tPHL
Characteristic
Maximum Toggle Frequency
Propagation Delay to Output
D
SEL
COMSEL
Min Typ Max Min Typ Max Min Typ Max Unit
1
GHz
ps
400
600 420
620 440
640
430
730 440
740 450
750
430
730 440
740 450
750
tSKEW
tSKEW
tJITTER
VPP
tr
tf
Within-Device Skew (Note 2)
Duty Cycle Skew (Note 3)
Random Clock Jitter (RMS)
Input Swing (Note 4)
Output Rise/Fall Times Q
(20% − 80%)
40
80
40
80
40
80
ps
100
100
100 ps
1.5
ps
150
1000 150
1000 150
1000 mV
200
540 200
540 200
540 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. VEE can vary +0.8 V / −0.5 V.
2. Within-device skew is defined as identical transitions on similar paths through a device.
3. Duty cycle skew is defined only for differential operation when the delays are measured from the cross point of the inputs to the cross point
of the outputs.
4. VPP(min) is minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈ 40.
www.onsemi.com
4
Share Link: 