MC100EL56(2016) データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
一致するリスト
MC100EL56 Datasheet PDF : 6 Pages
| |||
MC100EL56
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC PECL Mode Power Supply
VEE NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
VI ≤ VCC
VI ≥ VEE
8
V
−8
V
6
V
−6
Iout Output Current
Continuous
Surge
50
mA
100
IBB VBB Sink/Source
TA
Operating Temperature Range
Tstg Storage Temperature Range
qJA Thermal Resistance (Junction-to-Ambient)
0 lfpm
500 lfpm
SOIC−20 WB
± 0.5
−40 to +85
−65 to +150
90
60
mA
°C
°C
°C/W
qJC Thermal Resistance (Junction-to-Case)
Tsol Wave Solder (Pb-Free)
Standard Board
SOIC−20 WB
<2 to 3 sec @ 260°C
30 to 35
265
°C/W
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
Table 5. 100EL SERIES PECL DC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
IIH
IIL
Power Supply Current
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single-Ended)
Input LOW Voltage (Single-Ended)
Output Voltage Reference
Common Mode Range
(Differential Configuration) (Note 3)
VPP t 500 mV
VPP ≥ 500 mV
Input HIGH Current
Input LOW Current
20
24
20
24
20
24 mA
3915 3995 4120 3975 4045 4120 3975 4050 4120 mV
3170 3305 3445 3190 3295 3380 3190 3295 3380 mV
3835
4120 3835
4120 3835
4120 mV
3190
3525 3190
3525 3190
3525 mV
3.62
3.74 3.62
3.74 3.62
3.74 V
V
1.3
4.6 1.2
4.6 1.2
4.6
1.5
4.6 1.4
4.6 1.4
4.6
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin
and 1 V.
www.onsemi.com
3
Share Link: 