MC10EL34D(2000) データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
一致するリスト
MC10EL34D Datasheet PDF : 8 Pages
| |||
MC10EL34, MC100EL34
100EL SERIES PECL DC CHARACTERISTICS VCC= 5.0 V; VEE= 0.0 V (Note 1.)
–40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2.)
Output LOW Voltage (Note 2.)
Input HIGH Voltage (Single Ended)
Input LOW Voltage (Single Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3.)
39
39
42 mA
3915 3995 4120 3975 4045 4120 3975 4050 4120 mV
3170 3305 3445 3190 3295 3380 3190 3295 3380 mV
3835
4120 3835
4120 3835
4120 mV
3190
3525 3190
3525 3190
3525 mV
3.62
3.74 3.62
3.74 3.62
3.74 V
2.2
4.6 2.2
4.6 2.2
4.6
V
IIH
Input HIGH Current
150
150
150 µA
IIL
Input LOW Current
0.5
0.5
0.5
µA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / –0.5 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1V.
100EL SERIES NECL DC CHARACTERISTICS VCC= 0.0 V; VEE= –5.0 V (Note 1.)
–40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2.)
Output LOW Voltage (Note 2.)
Input HIGH Voltage (Single Ended)
Input LOW Voltage (Single Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3.)
39
39
42 mA
–1085 –1005 –880 –1025 –955 –880 –1025 –955 –880 mV
–1830 –1695 –1555 –1810 –1705 –1620 –1810 –1705 –1620 mV
–1165
–880 –1165
–880 –1165
–880 mV
–1810
–1475 –1810
–1475 –1810
–1475 mV
–1.38
–1.26 –1.38
–1.26 –1.38
–1.26 V
–2.8
–0.4 –2.8
–0.4 –2.8
–0.4 V
IIH
Input HIGH Current
150
150
150 µA
IIL
Input LOW Current
0.5
0.5
0.5
µA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / –0.5 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1V.
http://onsemi.com
4
Share Link: 