PM75CLB060 データシートの表示（PDF） - Powerex
部品番号
コンポーネント説明
一致するリスト
PM75CLB060 Datasheet PDF : 4 Pages
| |||
Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
PM75CLB060
Intellimod™ L-Series
Three Phase IGBT Inverter
75 Amperes/600 Volts
Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified
Characteristics
Symbol
Test Conditions
Min.
Typ. Max. Units
Control Sector
Short Circuit Trip Level
Short Circuit Current Delay Time
SC
toff(SC)
-20°C ≤ Tj ≤ 125°C, VD = 15V
VD = 15V
Over Temperature Protection
OT
Trip Level
(Detect Tj of IGBT Chip)
OTR
Reset Level
Supply Circuit Under-voltage Protection
UV
Trip Level
(-20 ≤ Tj ≤ 125°C)
UVR
Reset Level
Circuit Current
Input ON Threshold Voltage
Input OFF Threshold Voltage
ID
Vth(on)
Vth(off)
VD = 15V, VCIN = 15V, VN1-VNC
VD = 15V, VCIN = 15V, VXP1-VXPC
Applied between UP-VUPC,
VP-VVPC, WP-VWPC, UN- VN- WN-VNC
Fault Output Current*
IFO(H)
IFO(L)
VD = 15V, VCIN = 15V
VD = 15V, VCIN = 15V
Fault Output Pulse Width*
tFO
VD = 15V
*Fault output is given only when the internal SC, OT and UV protections schemes of either upper or lower devide operate to protect it.
150
100
135
—
11.5
—
—
—
1.2
1.7
—
—
1.0
—
—
145
125
12.0
12.5
20
5
1.5
2.0
—
10
1.8
— Amperes
—
µs
155
°C
—
°C
12.5 Volts
—
Volts
30
mA
10
mA
1.8
Volts
2.3
Volts
0.01
mA
15
mA
—
ms
Thermal Characteristics
Characteristic
Symbol
Condition
Min.
Junction to Case Thermal Resistance
Contact Thermal Resistance
Rth(j-c)Q
Rth(j-c)D
Rth(j-c)Q
Rth(j-c)D
Rth(c-f)
IGBT (Per 1/6 Module) (Note 1)
—
FWDi (Per 1/6 Module)(Note 1)
—
IGBT (Per 1/6 Module) (Note 2)
—
FWDi (Per 1/6 Module)(Note 2)
—
Case to Fin Per Module,
—
Thermal Grease Applied (Note 1)
** If you use this value, Rth(f-a) should be measured just under the chips.
Recommended Conditions for Use
Characteristic
Symbol
Condition
Supply Voltage
Control Supply Voltage***
Input ON Voltage
Input OFF Voltage
PWM Input Frequency
VCC
VD
VCIN(on)
VCIN(off)
fPWM
Applied across P-N Terminals
Applied between VUP1-VUPC,
VVP1-VVPC, VWP1-VWPC, VN1-VNC
Applied between UP-VUPC,
VP-VVPC, WP-VWPC, UN- VN- WN-VNC
Arm Shoot-through Blocking Time
tDEAD
Input Signal
*** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak.
Typ. Max. Units
—
0.42 °C/Watt
—
0.69 °C/Watt
—
0.32** °C/Watt
—
0.53** °C/Watt
—
0.038 °C/Watt
Value
≤400
15.0 ± 1.5
Units
Volts
Volts
≤0.8 Volts
≥9.0 Volts
≤20
kHz
≥2.0
µs
Note 1:TC (base plate) Measurement Point
Note 2: TC (under the chip) Measurement Point
TOP VIEW
Y
X
BOTTOM VIEW
TC
MEASUREMENT
POINT
Arm
Axis
X
Y
UP
VP
WP
UN
VN
WN
IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi
28.7 28.7 65.2 65.2 85.3 85.3 38.0 38.0 55.4 55.4 75.5 75.5
-6.6 0.85 -6.6 2.5 -6.6 2.5 4.6 -4.5 4.6 -4.5 4.6 -4.5
3
Share Link: 