AQW216AZ データシートの表示（PDF） - Panasonic Corporation
部品番号
コンポーネント説明
一致するリスト
AQW216AZ Datasheet PDF : 15 Pages
| |||
PhotoMOS® Cautions for Use
Current limit function (output current control)
1) Current limit function aims to increase resistance to surges when
the switch is turned on. Before using this function, connect the
varistor to the output as shown in the figure below.
1
4
Varistor
Surge: 10×160μs 1.6kV
2
3
* Set the varistor voltage to 150 V or less.
2) The current limit function capability can be lost if used longer than
the specified time. Be sure to set the output loss to the Max. rate.
Short circuit protection circuit
The short circuit protection circuit is designed to protect circuits from
excess current. Therefore, surge current may be detected as current
overload in which case the output current will be cut and the off
state maintained. For this reason, please include the inrush current
in the load current and keep it below the maximum load current.
Also, in order to maintain stability of internal IC operation, maintain
an input current of at least 5 mA (Latch type), 10 mA (Non Latch
type).
Photovoltaic MOSFET driver cautions for use
When two external MOSFETs are connected with a common source
terminal, oscillation may occur when operation is restored.
Therefore, please insert a 100 to 1,000 Ω resistor between the gate
terminal of the first MOSFET and the gate terminal of the second
MOSFET.
A typical example of this is given in the circuit below.
1
6
2
3
4
Input LED current (for Standard type)
For rising and dropping ratio of input LED current (di/dt), maintain
Min. 100 μA/s.
Input voltage (for Power voltage-sensitive type)
For rising and dropping ratio of input voltage (dv/dt), maintain Min.
100 mV/s.
Adjacent mounting (for Power type)
1) When devices are mounted close together with the heat-
generated devices, ambient temperature may rise abnormally.
Mounting layout and ventilation should be considered.
2) When many devices are mounted close together, load current
should be reduced. (Refer to the data of “Load current in adjacent
mounting vs. Ambient temperature characteristics.”)
Recommended load voltage
As a guide in selecting PhotoMOS®, please refer to the following
table.
1) Power photoMOS® (1 Form A)
Absolute maximum rating
Load voltage
Load current
Recommended
load voltage
AQZ102
60 V DC
4.0 A DC
5, 12, 24 V DC
DC AQZ105
type AQZ107
100 V DC
200 V DC
2.6 A DC
1.3 A DC
48 V DC
100 V DC
AQZ104
400 V DC
0.7 A DC
200 V DC
AQZ202
Peak AC, DC 60 V
Peak AC, DC 3.0 A
12 V AC
5, 12, 24 V DC
AC/
AQZ205
Peak AC, DC 100 V
Peak AC, DC 2.0 A
24 V AC
48 V DC
DC
type
AQZ207
Peak AC, DC 200 V
Peak AC, DC 1.0 A
48 V AC
100 V DC
AQZ204
Peak AC, DC 400 V
Peak AC, DC 0.5 A
120 V AC
200 V DC
2) Power photoMOS® (1 Form B)
Absolute maximum rating
Load voltage
Load current
Recommended
load voltage
AC/
DC
type
AQZ404
Peak AC, DC 400 V
Peak AC, DC 0.5 A
100 V AC
200 V DC
3) Power photoMOS® Voltage-sensitive type (1 Form A)
Absolute maximum rating
Load voltage
Load current
Recommended
load voltage
AQZ102D
60 V DC
3.6 A DC
5, 12, 24 V DC
DC AQZ105D
type AQZ107D
100 V DC
200 V DC
2.3 A DC
1.1 A DC
48 V DC
100 V DC
AQZ104D
400 V DC
0.6 A DC
200 V DC
AQZ202D
Peak AC, DC 60 V
Peak AC, DC 2.7 A
12 V AC
5, 12, 24 V DC
AC/
AQZ205D
Peak AC, DC 100 V
Peak AC, DC 1.8 A
24 V AC
48 V DC
DC
type
AQZ207D
Peak AC, DC 200 V
Peak AC, DC 0.9 A
48 V AC
100 V DC
AQZ204D
Peak AC, DC 400 V
Peak AC, DC 0.45 A
120 V AC
200 V DC
4) Power photoMOS® High Capacity type (1 Form A)
Absolute maximum rating
Load voltage
Load current
Recommended
load voltage
DC AQZ192
type AQZ197
60 V DC
200 V DC
10 A DC
5 A DC
5, 12, 24 V DC
100 V DC
AQZ202G
Peak AC, DC 60 V
Peak AC, DC 6 A
12 V AC
5, 12, 24 V DC
AC/
AQZ205G
Peak AC, DC 100 V
Peak AC, DC 4 A
24 V AC
48 V DC
DC
type
AQZ207G
Peak AC, DC 200 V
Peak AC, DC 2 A
48 V AC
100 V DC
AQZ206G2
Peak AC, DC 600 V
Peak AC, DC 1 A
120, 240 V AC
200, 400 V DC
Panasonic Corporation Electromechanical Control Business Division
industrial.panasonic.com/ac/e/
ー 14 ー
Panasonic Corporation 2020
ASCTB65E 202002
Share Link: 