FM25V01A
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Storage temperature ............................... –55 C to + 125 C
Maximum accumulated storage time
At 125 °C ambient temperature ................................. 1000 h
At 85 °C ambient temperature ................................ 10 Years
Ambient temperature
with power applied ................................... –55 °C to +125 °C
Supply voltage on VDD relative to VSS ........–1.0 V to + 4.5 V
Input voltage ........... –1.0 V to +4.5 V and VIN < VDD + 1.0 V
DC voltage applied to outputs
in HI-Z state ........................................ –0.5 V to VDD + 0.5 V
Transient voltage (< 20 ns) on
any pin to ground potential ................. –2.0 V to VDD + 2.0 V
Package power dissipation
capability (TA = 25 °C) ................................................. 1.0 W
Surface mount lead soldering
temperature (3 seconds) ........................................ + 260 C
DC output current (1 output at a time, 1-s duration) ... 15 mA
Electrostatic discharge voltage
Human Body Model (JEDEC Std JESD22-A114-B) ................ 2 kV
Charged Device Model (JEDEC Std JESD22-C101-A)........... 500 V
Latch-up current .................................................... > 140 mA
Operating Range
Range
Industrial
Ambient Temperature
(TA)
VDD
–40 C to +85 C 2.0 V to 3.6 V
DC Electrical Characteristics
Over the Operating Range
Parameter
Description
Test Conditions
Min
VDD
Power supply
2.0
IDD
VDD supply current
SCK toggling between VDD – fSCK = 40 MHz
–
0.2 V and VSS, other inputs VSS
or VDD – 0.2 V. SO = Open.
fSCK
=
1
MHz
–
ISB
VDD standby current
CS = VDD. All other inputs VSS or VDD.
–
IZZ
Sleep mode current
CS = VDD. All other inputs VSS or VDD.
–
ILI
Input leakage current VSS < VIN < VDD
–1
(Except HOLD)
Input leakage current
(for HOLD)
–100
ILO
VIH
VIL
VOH1
VOH2
VOL1
VOL2
Rin[4]
Output leakage current VSS < VOUT < VDD
Input HIGH voltage
Input LOW voltage
Output HIGH voltage IOH = –1 mA, VDD = 2.7 V.
Output HIGH voltage IOH = –100 A
Output LOW voltage
IOL = 2 mA, VDD = 2.7 V
Output LOW voltage
IOL = 150 A
Input resistance (HOLD) For VIN = VIL(max)
For VIN = VIH(min)
–1
0.7 × VDD
– 0.3
2.4
VDD – 0.2
–
–
800
30
Typ [3]
3.3
–
–
90
5
–
–
–
–
–
–
–
–
–
–
–
Max Unit
3.6
V
2.5
mA
0.22
mA
150
A
8
A
+1
A
+1
A
+1
A
VDD + 0.3 V
0.3 × VDD V
–
V
–
V
0.4
V
0.2
V
–
k
–
k
Notes
3. Typical values are at 25 °C, VDD = VDD(typ). Not 100% tested.
4. The input pull-up circuit is strong (30 k) when the input voltage is above VIH and weak (800 k) when the input voltage is below VIL.
Document Number: 001-90881 Rev. *E
Page 13 of 22