H2842F5 データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
一致するリスト
H2842F5 Datasheet PDF : 10 Pages
| |||
HA-2842
Absolute Maximum Ratings
Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . 35V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
Output Current (Notes 3, 4) . . . . . . . . . . . . . . . . . . . . . . . . . . 125mA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100mA (50% Duty Cycle)
Operating Conditions
Temperature Range
HA-2842-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
Recommended Supply Voltage Range . . . . . . . . . . . ±6.5V to ±15V
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W)
8 Lead SOIC Package . . . . . . . . . . . . . . . . . . . . . . .
160
Maximum Junction Temperature (Die) . . . . . . . . . . . . . . . . . . . .175oC
Maximum Junction Temperature (Plastic Package, Note 1) . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
(Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including output load, must be designed to maintain the maximum junction temperature below 150oC for plastic
packages. By using Application Note AN556 on Safe Operating Area equations, along with the packaging thermal resistances listed in the
Thermal Information section, proper load conditions can be determined.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
3. VO = ±5V, RL Unconnected, Duty cycle ≤ 50%. For information about using high output current amplifiers, please refer to Application Note AN556
(Thermal Safe-Operating-Areas For High Current Op Amps), and the “Power Dissipation Considerations” section in the “Application Information”
section of this datasheet.
4. Maximum continuous (100% Duty Cycle) output current is 50mA. For currents >50mA, Duty Cycle must be derated accordingly.
Electrical Specifications VSUPPLY = ±15V, RL = 1kΩ, CL ≤ 10pF, Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (oC)
HA-2842-5
MIN
TYP
MAX
INPUT CHARACTERISTICS
Offset Voltage (Note 10)
25
-
1
3
Full
-
-
6
Average Offset Voltage Drift
Full
-
13
-
Bias Current (Note 10)
25
-
5
10
Full
-
-
15
Average Bias Current Drift
Full
-
20
-
Offset Current
25
-
0.5
1.0
Full
-
-
1.5
Average Offset Current Drift
Full
-
1.3
-
Input Resistance
25
-
170
-
Input Capacitance
25
-
1
-
Common Mode Range
Full
±10
-
-
Input Noise Voltage
10Hz to 1MHz
25
-
16
-
Input Noise Voltage Density
Input Noise Current (Note 10)
TRANSFER CHARACTERISTICS
f = 1kHz, RSOURCE = 0Ω
f = 1kHz, RSOURCE = 100kΩ
25
-
16
-
25
-
2
-
Large Signal Voltage Gain
VO = ±10V
25
50
100
-
Full
30
60
-
Common-Mode Rejection Ratio (Note 10)
Minimum Stable Gain
VCM = ±10V
Full
80
110
-
25
2
-
-
Gain Bandwidth Product (Note 10)
Gain Flatness to 10MHz (Note 10)
AVCL = 100
RL ≥ 75Ω
25
-
80
-
25
-
±0.035
-
UNITS
mV
mV
µV/oC
µA
µA
nA/oC
µA
µA
nA/oC
kΩ
pF
V
µVRMS
nV⁄ Hz
pA ⁄ Hz
kV/V
kV/V
dB
V/V
MHz
dB
2
Share Link: 