ACT4515SH-T データシートの表示（PDF） - Active-Semi, Inc

部品番号

コンポーネント説明

一致するリスト

ACT4515SH-T

Wide-Input Sensorless CC/CV Step-Down DC/DC Converter

Active-Semi, Inc 

ACT4515

Rev 6, 14-Nov-12

STABILITY COMPENSATION

Figure 5:

Stability Compensation

COMP

ACT4515

CCOMP

RCOMP

CCOMP2c

c: CCOMP2 is needed only for high ESR output capacitor

The feedback loop of the IC is stabilized by the

components at the COMP pin, as shown in Figure

3. The DC loop gain of the system is determined by

the following equation:

AVDC

= 0.808 V

I OUT

AVEA GCOMP

(7)

The dominant pole P1 is due to CCOMP:

fP1

=

G EA

2 π AVEA C COMP

(8)

The second pole P2 is the output pole:

fP 2

=

I OUT

2πVOUT C OUT

(9)

The first zero Z1 is due to RCOMP and CCOMP:

fZ1

=

1

2πRCOMP CCOMP2

(10)

And finally, the third pole is due to RCOMP and

CCOMP2 (if CCOMP2 is used):

fP3

=

1

2πRCOMP CCOMP2

(11)

The following steps should be used to compensate

the IC:

STEP 1. Set the cross over frequency at 1/10 of the

switching frequency via RCOMP:

RCOMP

=

2πVOUT COUT fSW

10GEAGCOMP × 0.808V

= 2.75 × 10 8 VOUT COUT

(Ω)

(12)

STEP 2. Set the zero fZ1 at 1/4 of the cross over

frequency. If RCOMP is less than 15kΩ, the equation

for CCOMP is:

C COMP

= 1.8 × 10 −5

R COMP

(F)

(13)

If RCOMP is limited to 15kΩ, then the actual cross

over frequency is 3.4 / (VOUTCOUT). Therefore:

CCOMP = 1.2 ×10−5VOUTCOUT (F)

(14)

STEP 3. If the output capacitor’s ESR is high

enough to cause a zero at lower than 4 times the

cross over frequency, an additional compensation

capacitor CCOMP2 is required. The condition for using

CCOMP2 is:

RESRCOUT

≥

Min⎜⎜⎝⎛

1.1 ×10

COUT

−6

,0.012 ×VOUT

⎟⎟⎠⎞

(Ω)

(15)

And the proper value for CCOMP2 is:

CCOMP 2

= C R OUT ESRCOUT

RCOMP

(16)

Though CCOMP2 is unnecessary when the output

capacitor has sufficiently low ESR, a small value

CCOMP2 such as 100pF may improve stability against

PCB layout parasitic effects.

Table 2 shows some calculated results based on

the compensation method above.

Table 1:

Typical Compensation for Different Output

Voltages and Output Capacitors

VOUT

2.5V

3.3V

5V

2.5V

3.3V

5V

2.5V

3.3V

5V

COUT

RCOMP

22μF Ceramic 8.2kΩ

22μF Ceramic 12kΩ

22μF Ceramic 15kΩ

47μF SP CAP 15kΩ

47μF SP CAP 15kΩ

47μF SP CAP 15kΩ

470μF/6.3V/30mΩ 15kΩ

470μF/6.3V/30mΩ 15kΩ

470μF/6.3V/30mΩ 15kΩ

CCOMP CCOMP2c

2.2nF None

1.5nF None

1.5nF None

1.5nF None

1.8nF None

2.7nF None

15nF 47pF

22nF 47pF

27nF 47pF

c: CCOMP2 is needed for high ESR output capacitor.

CCOMP2 ≤ 47pF is recommended.

CC Loop Stability

The constant-current control loop is internally

compensated over the 400mA-1500mA output

range. No additional external compensation is

required to stabilize the CC current.

Output Cable Resistance Compensation

To compensate for resistive voltage drop across the

charger's output cable, the ACT4515 integrates a

Innovative PowerTM

-8-

www.active-semi.com

Copyright © 2012 Active-Semi, Inc.

Share Link: