CRGH0603F1R0 データシートの表示（PDF） - TE Connectivity

部品番号

コンポーネント説明

一致するリスト

CRGH0603F1R0

High Power Thick Film Chip Resistors

TE Connectivity 

Customer:

Part No.: CRGH Series

High Power Thick Film Chip Resistors

7. Performance specification :

Characteristics

Limits

Test Methods

( JIS C 5201-1 )

Dielectric

withstanding

voltage

No evidence of flashover

mechanical damage, arcing or

insulation break down

4.7 Clamped in the trough of a 90°C metallic v-block and

shall be tested at ac potential respectively specified in

the type for 60-70 seconds

4.8 Natural resistance change per temp. degree centigrade.

Temperature

Coefficient

See Page 2

R2-R1 x 106 (PPM/°C)

R1(t2-t1)

R1: Resistance value at room temperature (T1)

R2: Resistance value at room temp. plus 100°C (T2)

Test pattern: room temp. (T1), room temp. +100°C (T2)

Short time

Overload

Resistance change rate is

± 5% (2.0% + 0.1Ω) Max.

± 1% (1.0% + 0.1Ω) Max.

4.13 Permanent resistance change after the application

of a potential of 2.5 times RCWV for 5 seconds.

Wave Solder:

Test temperature of solder:

245°C ±3°C dipping time in solder : 2-3 seconds.

Reflow Solder:

Solderability 95 % coverage Min.

Soldering heat

Resistance change rate is:

±(1%+0.05Ω) Max.

Temperature

cycling

Resistance Change Rate Is

± 5% (1.0% + 0.05W) Max.

± 1% (0.5% + 0.05W) Max.

Humidity

Load life in

Humidty

Load Life

Terminal Bending

Resistance change rate is

± 5% (3.0% + 0.1W) Max.

± 1% (1.0% + 0.1W) Max.

Resistance change rate is

± 5% (3.0% + 0.1W) Max.

± 1% (1.0% + 0.1W) Max.

Resistance change rate is

± 5% (3.0% + 0.1W) Max.

± 1% (1.0% + 0.1W) Max.

Resistance change rate is

± (1.0% + 0.05W) Max.

1773204-1

4.18 Dip the resistor into a solder bath having a temperature

of 260°C ± 3°C and hold it for 10 ± 1 seconds.

4.19 Resistance change after continuous

5 cycles for duty cycle specified below :

Step Temperature

Time

1

-55°C ± 3°C

2

Room temp.

30 mins

10 ~ 15 mins

3

+155°C ± 2°C

30 mins

4

Room temp.

10 ~ 15 mins

4.24 Temporary resistance change after 240 hours

exposure in a humidity test chamber controlled at

40±2°C and 90-95% relative humidity

7.9 Resistance change after 1,000 hours (1.5 hours "on",

0.5 hour "off" ) at RCWV in a humidity chamber

controlled at 40°C ± 2°C and 90 to 95% relative humidity

4.25.1 Permanent resistance change after 1,000 hours

operating at RCWV, with duty cycle of

(1.5 hours"on", 0.5 hour"off") at 70°C ± 2°C ambient

4.33 Twist of Test Board :

Y/X = 3/90 mm for 60 seconds

Page 6.

2013/09/18--Version: 2

Share Link: