MP1430DN データシートの表示（PDF） - Monolithic Power Systems

部品番号

コンポーネント説明

一致するリスト

MP1430DN

3A, 28V, 385KHz Step-Down Converter

Monolithic Power Systems 

MP1430 – 3A, 28V, 385KHz STEP-DOWN CONVERTER

Output Rectifier Diode

The output rectifier diode supplies the current to

the inductor when the high-side switch is off. To

reduce losses due to the diode forward voltage

and recovery times, use a Schottky diode.

Choose a diode whose maximum reverse

voltage rating is greater than the maximum

input voltage, and whose current rating is

greater than the maximum load current. Table 2

lists example Schottky diodes and

manufacturers.

Table 2—Diode Selection Guide

Diode

SK33

SK34

B330

B340

MBRS330

MBRS340

Voltage/Current

Rating

Manufacturer

30V, 3A

Diodes Inc.

40V, 3A

Diodes Inc.

30V, 3A

Diodes Inc.

40V, 3A

Diodes Inc.

30V, 3A

On Semiconductor

40V, 3A

On Semiconductor

Input Capacitor

The input current to the step-down converter is

discontinuous, therefore a capacitor is required

to supply the AC current to the step-down

converter while maintaining the DC input

voltage. Use low ESR capacitors for the best

performance. Ceramic capacitors are preferred,

but tantalum or low-ESR electrolytic capacitors

may also suffice.

Since the input capacitor absorbs the input

switching current it requires an adequate ripple

current rating. The RMS current in the input

capacitor can be estimated by:

ICIN = ILOAD ×

VOUT

VIN

×⎜⎜⎛1−

⎝

VOUT

VIN

⎟⎞

⎟

⎠

The worst-case condition occurs at VIN = 2VOUT,

where:

ICIN

=

ILOAD

2

For simplification, choose the input capacitor

whose RMS current rating greater than half of

the maximum load current.

The input capacitor can be electrolytic, tantalum

or ceramic. When using electrolytic or tantalum

capacitors, a small, high quality ceramic

capacitor, i.e. 0.1µF, should be placed as close

to the IC as possible. When using ceramic

capacitors, make sure that they have enough

capacitance to provide sufficient charge to

prevent excessive voltage ripple at input. The

input voltage ripple caused by capacitance can

be estimated by:

∆VIN

=

ILOAD

fS × CIN

×

VOUT

VIN

× ⎜⎜⎝⎛1 −

VOUT

VIN

⎟⎟⎠⎞

Where CIN is the input capacitance value.

Output Capacitor

The output capacitor is required to maintain the

DC output voltage. Ceramic, tantalum, or low

ESR electrolytic capacitors are recommended.

Low ESR capacitors are preferred to keep the

output voltage ripple low. The output voltage

ripple can be estimated by:

∆VOUT

=

VOUT

fS × L

×

⎜⎜⎝⎛1 −

VOUT

VIN

⎟⎟⎠⎞ × ⎜⎜⎝⎛RESR

+

1

8 × fS × CO

⎟⎟⎠⎞

Where L is the inductor value, CO is the output

capacitance value, and RESR is the equivalent

series resistance (ESR) value of the output

capacitor.

In the case of ceramic capacitors, the

impedance at the switching frequency is

dominated by the capacitance. The output

voltage ripple is mainly caused by the

capacitance. For simplification, the output

voltage ripple can be estimated by:

∆VOUT

=

VOUT

8 × fS2 × L × CO

× ⎜⎜⎝⎛1−

VOUT

VIN

⎟⎟⎠⎞

In the case of tantalum or electrolytic

capacitors, the ESR dominates the impedance

at the switching frequency. For simplification,

the output ripple can be approximated to:

∆VOUT

=

VOUT

fS × L

×

⎜⎜⎝⎛1

−

VOUT

VIN

⎟⎟⎠⎞ × RESR

The characteristics of the output capacitor also

affect the stability of the regulation system. The

MP1430 can be optimized for a wide range of

capacitance and ESR values.

MP1430 Rev. 1.0

11/1/2005

www.MonolithicPower.com

7

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.

© 2005 MPS. All Rights Reserved.

Free Datasheet http://www.datasheet4u.com/

Share Link: