PM50RVA120 データシートの表示（PDF） - Mitsumi
部品番号
コンポーネント説明
一致するリスト
PM50RVA120 Datasheet PDF : 7 Pages
| |||
MITSUBISHI <INTELLIGENT POWER MODULES>
PM50RVA120
FLAT-BASE TYPE
INSULATED PACKAGE
CONTROL PART
Symbol
Parameter
Test Condition
Limits
Min.
Typ.
Max. Unit
ID
Circuit Current
VD = 15V, VCIN = 15V
VN1-VNC
V*P1-V*PC
—
44
60
mA
—
13
18
Vth(ON) Input ON Threshold Voltage Applied between : UP-VUPC, VP-VVPC, WP-VWPC
Vth(OFF) Input OFF Threshold Voltage
UN • VN • WN • Br-VNC
1.2
1.5
1.8
V
1.7
2.0
2.3
OC
Over Current Trip Level
–20 ≤ Tj ≤ 125°C, VD = 15V, Break part
22
—
—
A
SC
Short Circuit Trip Level
–20≤ Tj ≤ 125°C, VD = 15V
Inverter part
59
—
—
A
Brake part
—
52
—
toff(OC) Over Current Delay Time
VD = 15V, Break part
—
10
—
µs
toff(SC)
Short Circuit Current Delay
Time
VD = 15V
—
10
—
µs
OT
Over Temperature Protection Base-plate
Trip level
OTr
Temperature detection, VD = 15V
Reset level
111
118
125
°C
—
100
—
UV
Supply Circuit Under-Voltage
UVr
Protection
–20 ≤ Tj ≤ 125°C
Trip level
Reset level
11.5
12.0 12.5
V
—
12.5
—
IFO(H)
IFO(L)
Fault Output Current
VD = 15V, VFO = 15V
—
(Note-2)
—
—
0.01
mA
10
15
Minimum Fault Output Pulse
tFO
Width
VD = 15V
(Note-2) 1.0
1.8
—
ms
(Note-2) Fault output is given only when the internal SC, OT & UV protection.
Fault output of OT protection operate by lower arm.
Fault output of OT, UV protection given pulse while over level.
THERMAL RESISTANCES
Symbol
Rth(j-c)Q
Rth(j-c)F
Rth(j-c)Q
Rth(j-c)F
Rth(c-f)
Parameter
Junction to case Thermal
Resistances
Contact Thermal Resistance
Test Condition
Inverter IGBT part (per 1/6 module)
Inverter FWDi part (per 1/6 module)
Brake IGBT part
Brake FWDi part
Case to fin, Thermal grease applied (per 1 module)
Limits
Min.
Typ.
Max. Unit
—
—
0.37
—
—
0.70
—
—
0.93 °C/W
—
—
1.50
—
—
0.027
MECHANICAL RATINGS AND CHARACTERISTICS
Symbol
—
—
—
Parameter
Mounting torque
Mounting torque
Weight
Mounting part
Main terminal
Test Condition
—
Limits
Min.
Typ.
Unit
Max.
screw : M5
2.5
3.0
3.5 N • m
screw : M5
2.5
3.0
3.5 N • m
—
560
—
g
RECOMMENDED CONDITIONS FOR USE
Symbol
Parameter
VCC
Supply Voltage
VD
Control Supply Voltage
Test Condition
Recommended value
Unit
Applied across P-N terminals
≤ 800
V
Applied between : VUP1-VUPC, VVP1-VVPC
VWP1-VWPC, VN1-VNC
(Note-3)
15 ± 1.5
V
VCIN(ON)
VCIN(OFF)
tdead
Input ON Voltage
Input OFF Voltage
Arm Shoot-through
Blocking Time
Applied between : UP-VUPC, VP-VVPC, WP-VWPC
UN • VN • WN • Br-VNC
For IPM’s each input signals
≤ 0.8
≥ 4.0
V
≥ 3.0
µs
fPWM
PWM Input Frequency
Using Application Circuit input signal of IPM,
Sinusoidal PWM VVVF inverter
≤ 20
kHz
(Note-3) With ripple satisfying the following conditions dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak
Jun. 2005
Share Link: 