LM293D データシートの表示（PDF） - Motorola => Freescale
部品番号
コンポーネント説明
一致するリスト
LM293D Datasheet PDF : 6 Pages
| |||
LM393, LM393A, LM293, LM2903, LM2903V
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Power Supply Voltage
Input Differential Voltage Range
Input Common Mode Voltage Range
VCC
VIDR
VICR
+36 or ±18
Vdc
36
Vdc
–0.3 to +36 Vdc
Output Short Circuit–to–Ground
Output Sink Current (Note 1)
Power Dissipation @ TA = 25°C
Derate above 25°C
Operating Ambient Temperature Range
LM293
LM393, 393A
LM2903
LM2903V
ISC
ISink
PD
1/RθJA
TA
Continuous
20
570
5.7
–25 to +85
0 to +70
–40 to +105
–40 to +125
mA
mW
mW/°C
°C
Maximum Operating Junction Temperature
LM393, 393A, 2903, LM2903V
LM293
TJ(max)
°C
125
150
Storage Temperature Range
Tstg
–65 to +150
°C
ELECTRICAL CHARACTERISTICS (VCC = 5.0 Vdc, Tlow ≤ TA ≤ Thigh,* unless otherwise noted.)
LM393A
Characteristic
Symbol
Min
Typ
Max
Unit
Input Offset Voltage (Note 2)
TA = 25°C
Tlow ≤ TA ≤ Thigh
Input Offset Current
TA = 25°C
Tlow ≤ TA ≤ Thigh
Input Bias Current (Note 3)
TA = 25°C
Tlow ≤ TA ≤ Thigh
Input Common Mode Voltage Range (Note 4)
TA = 25°C
Tlow ≤ TA ≤ Thigh
Voltage Gain RL ≥ 15 kΩ, VCC = 15 Vdc, TA = 25°C
Large Signal Response Time
Vin = TTL Logic Swing, Vref = 1.4 Vdc
VRL = 5.0 Vdc, RL = 5.1 kΩ, TA = 25°C
Response Time (Note 5) VRL = 5.0 Vdc, RL = 5.1 kΩ, TA = 25°C
Input Differential Voltage (Note 6)
All Vin ≥ Gnd or V– Supply (if used)
VIO
IIO
IIB
VICR
AVOL
–
tTLH
VID
mV
–
±1.0
±2.0
–
–
4.0
nA
–
±50
±50
–
–
±150
nA
–
25
250
–
–
400
V
0
–
VCC –1.5
0
–
VCC –2.0
50
200
–
V/mV
–
300
–
ns
–
1.3
–
µs
–
–
VCC
V
Output Sink Current
Vin ≥ 1.0 Vdc, Vin+ = 0 Vdc, VO ≤ 1.5 Vdc, TA = 25°C
ISink
6.0
16
–
mA
Output Saturation Voltage
Vin ≥ 1.0 Vdc, Vin+ = 0 Vdc, ISink ≤ 4.0 mA, TA = 25°C
Tlow ≤ TA ≤ Thigh
VOL
mV
–
150
400
–
–
700
* Tlow = 0°C, Thigh = +70°C for LM393/393A
NOTES: 1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC, output short circuits to VCC can cause excessive
] heating and eventual destruction.
2. At output switch point, VO 1.4 Vdc, RS = 0 Ω with VCC from 5.0 Vdc to 30 Vdc, and over the full input common mode range (0 V to VCC = –1.5 V).
3. Due to the PNP transistor inputs, bias current will flow out of the inputs. This current is essentially constant, independent of the output state, there
fore, no loading changes will exist on the input lines.
4. Input common mode of either input should not be permitted to go more than 0.3 V negative of ground or minus supply. The upper limit of common
mode range is VCC –1.5 V.
5. Response time is specified with a 100 mV step and 5.0 mV of overdrive. With larger magnitudes of overdrive faster response times are obtainable.
6. The comparator will exhibit proper output state if one of the inputs becomes greater than VCC, the other input must remain within the common mode
range. The low input state must not be less than –0.3 V of ground or minus supply.
2
MOTOROLA ANALOG IC DEVICE DATA
Share Link: 