WM9704M データシートの表示（PDF） - Wolfson Microelectronics plc

部品番号

コンポーネント説明

メーカー

WM9704M

AMC’97 Audio and Modem Codec

Wolfson Microelectronics plc 

WM9704M

Production Data

The datastreams currently defined by the AC’97 specification include:

PCM playback - 2 output slots

2-channel composite PCM output stream

PCM record data - 2 input slots

2-channel composite PCM input stream

Control - 2 output slots

Control register write port

Status - 2 input slots

Control register read port

Optional modem line codec output -

1 output slot

Modem line codec DAC input stream

Optional modem line codec input -

1 input slot

Modem line codec ADC output stream

Optional dedicated microphone input -

1 input slot

Dedicated microphone input stream in support

of stereo AEC and/or other voice applications.

Synchronisation of all AC-link data transactions is signalled by the WM9704M controller. The

WM9704M drives the serial bit clock onto AC-link, which the AC’97 controller then qualifies with a

synchronisation signal to construct audio frames.

SYNC, fixed at 48kHz, is derived by dividing down the serial clock (BIT_CLK). BIT_CLK, fixed at

12.288MHz, provides the necessary clocking granularity to support 12, 20-bit outgoing and incoming

time slots. AC-link serial data is transitioned on each rising edge of BIT_CLK. The receiver of AC-link

data, (WM9704M for outgoing data and AC’97 controller for incoming data), samples each serial bit

on the falling edges of BIT_CLK.

The AC-link protocol provides for a special 16-bit time slot (slot 0) wherein each bit conveys a valid

tag for its corresponding time slot within the current audio frame. A “1” in a given bit position of slot 0

indicates that the corresponding time slot within the current audio frame has been assigned to a data

stream, and contains valid data. If a slot is “tagged” invalid, it is the responsibility of the source of the

data, (the WM9704M for the input stream, AC’97 controller for the output stream), to stuff all bit

positions with 0s during that slot’s active time.

SYNC remains high for a total duration of 16 BIT_CLKs at the beginning of each audio frame.

The portion of the audio frame where SYNC is high is defined as the “Tag Phase”. The remainder of

the audio frame where SYNC is low is defined as the “Data Phase”. Additionally, for power savings,

all clock, sync, and data signals can be halted. This requires that the WM9704M be implemented as

a static design to allow its register contents to remain intact when entering a power savings mode.

AC-LINK AUDIO OUTPUT FRAME (SDATA_OUT)

The audio output frame data streams correspond to the multiplexed bundles of all digital output data

targeting the WM9704M’s DAC inputs, and control registers. As briefly mentioned earlier, each audio

output frame supports up to 12 20-bit outgoing data time slots. Slot 0 is a special reserved time slot

containing 16-bits, which are used for AC-link protocol infrastructure.

OUTPUT TAG SLOT (16-BITS)

Bit (15)

Bit (14)

Bit (13)

Bit (12:3)

Bit 2

Bit (1:0)

Frame Valid

Slot 1 Valid Command Address bit

Slot 2 Valid Command Data bit

Slot 3-12 Valid bits as defined by AC’97

Reserved

2-bit Codec ID field

New definitions for Secondary Codec Register Access

(Primary Codec only)

(Primary Codec only)

(Set to 0)

(00 reserved for Primary; 01, 10, 11

indicate Secondary)

Within slot 0 the first bit is a global bit (SDATA_OUT slot 0, bit 15) which flags the validity for the

entire audio frame. If the “Valid Frame” bit is a 1, this indicates that the current audio frame contains

at least one time slot of valid data. The next 12-bit positions sampled by the WM9704M indicate

which of the corresponding 12 time slots contain valid data.

WOLFSON MICROELECTRONICS LTD

PD Rev 3.2 January 2001

18

Share Link: