UPC8158K(2001) データシートの表示（PDF） - NEC => Renesas Technology
部品番号
コンポーネント説明
一致するリスト
UPC8158K Datasheet PDF : 5 Pages
| |||
UPC8158K
ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C)
SYMBOLS
PARAMETERS
UNITS RATINGS
VCC Supply Voltage
V
5.0
VPS/VAGC Power Save & AGC Control V
5.0
PD
Power Dissipation2
mW
430
TA
Operating Ambient Temp.
°C
-40 to +85
TSTG Storage Temperature
°C -55 to +150
Note:
1. Operation in excess of any one of these conditions may result in
permanent damage.
2. TA = +85º C
PIN EXPLANATIONS
RECOMMENDED
OPERATING CONDITIONS
PART NUMBER
UPC8158K
SYMBOLS
PARAMETERS
UNITS MIN TYP MAX
VCC Supply Voltage
V 2.7 3.0 4.0
VPS
Power Save Voltage
V
0
0.3
VAGCPS AGC Control Voltage
V 1.0
2.5
TA
Operating Ambient Temp. °C -30 +25 +80
fRFout Upconv. RF Output Freq. MHz 800
1500
fLO2in LO2 Input Frequency
MHz 600
1750
fI/Qin
I/Q Input Frequency
MHz DC
10
PLO1in LO1 Input Level
dBm -18 -15 -12
PLO2in LO2 Input Level
dBm -18 -15 -12
VI/Qin I/Q Input Amplitude
mVP-P
420 500
fUPCONin Upconverter Input Freq.
fMODout Modulator Output Freq.
MHz 100
300
fLO1in LO1 Input Frequency
PIN
SYMBOL
SUPPLY
PIN
NO.
VOLTAGE (V) VOLTAGE (V)
FUNCTION AND APPLICATION
1
lin
Vcc/2
Input for I signal. This input impedance
–
is 200 kΩ. In the case of that I/Q input
signals are single ended, amplitude of
the signal 500 m VP-P max.
EQUIVALENT CIRCUIT
Input for I signal. This input impedance
2
linb
Vcc/2
–
is 200 kΩ. In the case of that I/Q input
1
2
signals are single ended,Vcc/2 biased
DC signal should be input. In the case of
the I/Q input signals are differential,
amplitude of the signal is 500 m VP-P
max.
3
N.C.
–
–
This pin is not connected to internal
circuit. This pin should be opened or
grounded.
4
Qinb
Vcc/2
–
Input for Q signal. This input impedance
is 200 KΩ. In the case of that I/Q input
signals are single ended, amplitude of
the signal is 500 m VP-P max.
Input for I signal. This input impedance
5
Qin
Vcc/2
–
is 200 kΩ. In the case of that I/Q input
4
5
signals are single ended,Vcc/2 biased
DC signal should be input. In the case of
the I/Q input signals are differential,
amplitude of the signal is 500 m VP-P
max.
6
N.C.
–
7
N.C.
–
–
These pins is not connected to internal
–
circuit. These pins should be opened or
grounded.
8
N.C.
–
–
9
LO1inb
–
2.98
Bypass pin of modulator's local input.
This pin should be decoupled with 330
pF capacitor.
9
10
10
LO1in
–
2.98
Local signal for modulator. This pin must
be coupled with DC cut capacitor 330 pF
and should be terminated with 51 Ω
resistor
11
Vcc
2.7 to 4.0
–
Supply Voltage pin modulator, up-
converter and AGC circuits.
Share Link: 