SC4607 データシートの表示（PDF） - Semtech Corporation

部品番号

コンポーネント説明

一致するリスト

SC4607

Very Low Input, MHz Operation,High Efficiency Synchronous Buck

Semtech Corporation 

SC4607

POWER MANAGEMENT

Application Information

Enable:

The SC4607 is enabled by applying a voltage greater than

2.25 volts to the VCC pin. The SC4607 is disabled when

VCC falls below 1.95 volts or when sleep mode opera-

tion is invoked by clamping the FS/SYNC pin to a voltage

below 75mV. 10µA is the typical current drawn through

the VCC pin during sleep mode. During the sleep mode,

the high side and low side MOSFETs are turned off and

the internal soft start voltage is held low.

Oscillator:

then connected to the junction of the external timing

capacitor and the added resistor as shown in Figure 1.

External

Clock

Signal

SC4607

FS/SYNC

Ctiming

Rsync

100 ohm

The FS/SYNC pin is used to set the PWM oscillator fre-

quency through an external timing capacitor that is con-

nected from the FS/SYNC pin to the GND pin. The re-

sulting ramp waveform on the FS/SYNC pin is a triangle

at the PWM frequency with a peak voltage of 1.3V and a

valley voltage of 0.3V. The PWM duty ratio is limited by

the ramp to a maximum of 97%, which allows the boot-

strap capacitor to be charged during each cycle. The ca-

pacitor tolerance adds to the accuracy of the oscillator

frequency. The approximate operating frequency and soft

start time are both determined by the value of the exter-

nal timing capacitor as shown in Table 1.

External Timing

Capacitor Value

(pF)

Frequency

(kHz)

120

1000

270

580

560

350

Soft Start Time (µs)

628

1220

1838

Table 1: Operating Frequency and Soft Start Time

Values Based On the Value of the External Timing

Capacitor Placed Across the FS/SYNC and GND Pins

Synchronous mode operation is invoked by using a sig-

nal from an external clock. A low value resistor (100Ω

typical) must be inserted in series with the timing capaci-

tor between the timing capacitor and the GND pin. The

other terminal of the timing capacitor will remain con-

nected to the FS/SYNC pin. The external clock signal is

Figure 1

UVLO:

When the FS/SYNC pin is not pulled and held below 75mV,

the voltage on the Vcc pin determines the operation of

the SC4607. As Vcc increases during start up, the UVLO

block senses Vcc and keeps the high side and low side

MOSFETs off and the internal soft start voltage low until

Vcc reaches 2.25V. If no faults are present, the SC4607

will initiate a soft start when Vcc exceeds 2.25V. A hys-

teresis (100mV) in the UVLO comparator provides noise

immunity during its start up.

Soft Start:

The soft start function is required for step down control-

lers to prevent excess inrush current through the DC bus

during start up. Generally this can be done by sourcing a

controlled current into a timing capacitor and then using

the voltage across this capacitor to slowly ramp up the

error amp reference. The closed loop creates narrow

width driver pulses while the output voltage is low and

allows these pulses to increase to their steady state duty

cycle as the output voltage reaches its regulated value.

With this, the inrush current from the input side is con-

trolled. The duration of the soft start in the SC4607 is

controlled by an internal timing circuit which is used dur-

ing start up and over current to set the hiccup time. The

soft start time can be obtained from Table 1.

The SC4607 implements its soft start by ramping up the

error amplifier reference voltage providing a controlled

 2005 Semtech Corp.

8

www.semtech.com

Share Link: