MP1 データシートの表示（PDF） - Emerson Network Power

部品番号

コンポーネント説明

一致するリスト

MP1

400-1200 Watts MP Series

Emerson Network Power 

AMERICAS

5810 Van Allen Way

Carlsbad, CA 92008

Telephone: 760-930-4600

Facsimile: 760-930-0698

EUROPE

Astec House, Waterfront Business Park

Merry Hill, Dudley

West Midlands, DY5 1LX, UK

Telephone: 44 (1384) 842-211

Facsimile: 44 (1384) 843-355

ASIA

Units 2111-2116, Level 21

Tower1, Metroplaza

223, Hing Fong Road

Kwai Fong, New Territories

Hong Kong

Telephone: 852-2437-9662

Facsimile: 852-2402-4426

Electrical Specs

Input

Input voltage

Frequency

Inrush current

Efficiency

Power factor

Turn-on time

EMI filter standard

EMI filter

(low leakage option)

Leakage current standard

Leakage current

(low leakage option).

Radiated EMI

Holdover storage

AC OK

Harmonic distortion

Isolation

Global Inhibit/Enable

Input fuse (internal)

Warranty

85-264 VAC

120-350 VDC

47-440 Hz

40 A peak max. (soft start)

70-80% typ. @ full case load

0.99 typ. meets EN61000-3-2

AC on 1.5 sec typ.,

Inhibit / Enable 150 ms typ.

CISPR 22

EN55022 Level “B”

CISPR 22

EN55022 Level “A”

2.0 mA max. @ 240 VAC

300 μA max. @ 240 VAC

CISPR 22

EN55022 Level “B”

20 ms minimum

(independent of input VAC)

>5 ms early warning min.

before outputs loose regulation

Full cycle ride thru (50 Hz)

Meets EN61000-3-2

Meets EN60950

TTL, Logic “1” and Logic “0”

MP4: 10 A

MP6: 15 A

MP8: 20 A

MP1: 20 A

2 years

Output

Adjustment range

Margining

Overall reg

Ripple

Dynamic response

Recovery time

Overcurrent protection

Short circuit protection

Overvoltage protection

(measured at sense

connection)

Reverse voltage protection

Thermal protection

Remote sense

100

80

%

Rated

60

Total

Case

Load

40

20

Power Derating Curve

50

Single wire parallel

DC OK

Minimum load

Normal Housekeeping bias voltage

Air Flow

Module inhibit

50

Switching frequency

Output/Output isolation

VME signal option board

Hold-up module (HUP)

30 35 40 45 50 55 60 65 70

TA – Ambient Temperature – °C

±10% min. all outputs

±4-6% nom.1

0.4% or 20 mV max.

(36 W modules 4% max.)

RMS: 0.1% or 10 mV, whichever is greater

Pk-Pk: 1.0% or 50 mV, whichever is greater

Bandwidth limited to 20 MHz

<2% or 100 mV, with 25% load step.

To within 1% in <300 μsec.

Single, main of dual output module

105-120% of rated output current.

Aux output of dual output module 105-140%

of rated output current.

Triple output module internally protected

Protected for continuous short circuit

Recovery is automatic upon removal of short.

Single output modules

2-5.5 V 122-134%

6-60 V 110-120%

Dual output module

2-6 V 122-134%

8-28 V 110-120%

Triple output module.

No overvoltage protection provided. Recycle

the AC input voltage to reset OVP circuit

100% of rated output current

All outputs disabled when internal temp

exceeds safe operating range. >5 ms warning

(AC OK signal) before shutdown

Up to 0.5 V total drop (not available on triple

output module)

Current share to within 2% of total rated current2

-2% to -8% of nominal for any monitored output2

Not required on single or triple output modules.

10% required on main of dual output modules3

5 VDC @1.0A mA max. present whenever AC

input is applied

TTL, isolated, singles and dual

(both outputs) only

250 kHz

>1 Megohm

POR signal & quad external DC OK

1-slot module providing an additional

34mSec (60mSec total)

hold-up @ 600W loading.

Notes:

1. Single output modules only.

2. Single and main of dual output modules only.

3. Contact factory for optional preload if required.

www.astecpower.com

137

Share Link: