MP2351 データシートの表示（PDF） - Monolithic Power Systems

部品番号

コンポーネント説明

一致するリスト

MP2351

1.5A, 23V, 1.4MHz Step-Down Converter

Monolithic Power Systems 

TM

MP2351 – 1.5A, 23V, 1.4MHz STEP-DOWN CONVERTER

The input capacitor can be electrolytic, tantalum

or ceramic. When using electrolytic or tantalum

capacitors, a small, high quality ceramic

capacitor, i.e. 0.1µF, should be placed as close

to the IC as possible. When using ceramic

capacitors, make sure that they have enough

capacitance to provide sufficient charge to

prevent excessive voltage ripple at input. The

input voltage ripple caused by capacitance can

be estimated by:

∆VIN

=

ILOAD ×

fS × C1

VOUT

VIN

× ⎜⎜⎝⎛1 −

VOUT

VIN

⎟⎟⎠⎞

Output Capacitor

The output capacitor is required to maintain the

DC output voltage. Ceramic, tantalum, or low

ESR electrolytic capacitors are recommended.

Low ESR capacitors are preferred to keep the

output voltage ripple low. The output voltage

ripple can be estimated by:

∆VOUT

=

VOUT

fS × L

×

⎜⎜⎝⎛1

−

VOUT

VIN

⎟⎟⎠⎞ × ⎜⎜⎝⎛RESR

+

8

×

1

fS ×

C2

⎟⎟⎠⎞

Where RESR is the equivalent series resistance

(ESR) value of the output capacitor and C2 is

the output capacitance value.

In the case of ceramic capacitors, the

impedance at the switching frequency is

dominated by the capacitance. The output

voltage ripple is mainly caused by the

capacitance. For simplification, the output

voltage ripple can be estimated by:

∆VOUT

=

8

×

VOUT

fS2 × L

×

C2

×

⎜⎜⎝⎛1

−

VOUT

VIN

⎟⎟⎠⎞

In the case of tantalum or electrolytic

capacitors, the ESR dominates the impedance

at the switching frequency. For simplification,

the output ripple can be approximated to:

∆VOUT

=

VOUT

fS × L

×

⎜⎜⎝⎛1 −

VOUT

VIN

⎟⎟⎠⎞ × RESR

The characteristics of the output capacitor also

affect the stability of the regulation system. The

MP2351 can be optimized for a wide range of

capacitance and ESR values.

Compensation Components

The MP2351 employs current mode control for

easy compensation and fast transient response.

The system stability and transient response are

controlled through the COMP pin. COMP pin is

the output of the internal transconductance

error amplifier. A series capacitor-resistor

combination sets a pole-zero combination to

control the characteristics of the control system.

The DC gain of the voltage feedback loop is:

A VDC

= RLOAD

× GCS

× A VEA

×

VFB

VOUT

Where AVEA is the error amplifier voltage gain,

GCS is the current sense transconductance and

RLOAD is the load resistor value.

The system has two poles of importance. One

is due to the compensation capacitor (C3) and

the output resistor of error amplifier, and the

other is due to the output capacitor and the load

resistor. These poles are located at:

fP1

=

GEA

2π × C3 × A VEA

fP2

=

1

2π × C2 × RLOAD

Where GEA is the error amplifier

transconductance.

The system has one zero of importance, due to

the compensation capacitor (C3) and the

compensation resistor (R3). This zero is located

at:

fZ1

=

1

2π × C3 × R3

The system may have another zero of

importance, if the output capacitor has a large

capacitance and/or a high ESR value. The zero,

due to the ESR and capacitance of the output

capacitor, is located at:

fESR

=

1

2π × C2 × RESR

MP2351 Rev. 1.5

www.MonolithicPower.com

6

1/6/2006

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.

© 2006 MPS. All Rights Reserved.

Share Link: