MC10SX1190(1999) データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
一致するリスト
MC10SX1190 Datasheet PDF : 8 Pages
| |||
MC10SX1190
DC CHARACTERISTICS (Note 1)
-40°C
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit
VOH
Output Voltage High (QR,QR)
VCC = 5.0V, VEE = 0V (Notes 2,3)
4.01
4.04
4.06
4.16
V
VOL
Output Voltage Low (QR,QR)
VCC = 5.0V, VEE = 0V (Notes 2,3)
3.23
3.26
3.28
3.33
V
VOH
Output Voltage High (QT,QT)
VCC = 5.0V, VEE = 0V (Notes 2,4)
3.94
3.98
4.04
4.13
V
VOL
Output Voltage Low (QT,QT)
VCC = 5.0V, VEE = 0V (Notes 2,4)
2.51
2.49
2.48
2.47
V
ICC
Quiescent Supply Current (Note 5)
55
mA
VIH
Input Voltage High (DR,DR & DT,DT)
VCC = 5.0V, VEE = 0V (Note 2)
3.77
4.11 3.83
4.16 3.87
4.19 3.94
4.28 V
VIL
Input Voltage Low (DR,DR & DT,DT)
VCC = 5.0V, VEE = 0V (Note 2)
3.05
3.50 3.05
3.52 3.05
3.52 3.05
3.56 V
VIH
Input Voltage High SEL (Note 6)
2.0
2.0
2.0
2.0
V
VIL
Input Voltage Low SEL (Note 6)
0.8
0.8
0.8
0.8 V
VBB
Output Reference Voltage
VCC = 5.0V, VEE = 0V (Note 2)
3.57
3.63
3.70
3.62
3.67
3.73
3.65
3.70
3.75
3.69
3.75
3.81
V
1. 10SX circuits are designed to meet the DC specifications shown in the table after thermal equilibrium has been established. The circuit is mounted in a test socket
or mounted on a printed circuit board and transverse air greater than 500lfm is maintained.
2. Values will track 1:1 with the VCC supply.
3. Outputs loaded with 50Ω to +3.0V
4. Outputs loaded with 50Ω to +2.0V
5. Outputs open circuited.
6. TTL signal threshold is 1.5V above VEE.
AC CHARACTERISTICS (Note 1 & 7)
–40°C
0 to 85°C
Symbol
Characteristic
Min
Typ Max Min
Typ Max Unit
Condition
tPLH, tPHL Propagation Delay DR QR (Diff)
to Output
(SE)
240
ps Note 2
240
Note 3
DR QT (Diff)
425
(SE)
425
DT QT (Diff)
425
(SE)
425
tPLH, tPHL Propagation Delay SEL QT,QT 450
600
850
500
650
800
ps 1.5V to 50% Pt
tr,
Rise Time
tf
Fall Time
QR,QR
118
ps 20% to 80%
118
80% to 20%
tr,
Rise Time
tf
Fall Time
QT,QT
230
ps 20% to 80%
230
80% to 20%
tskew
Within Device Skew
15
15
ps Note 4
VPP
Minimum Input Swing
200
200
mV Note 5
VCMR
Common Mode Range
3.0
4.35
3.0
4.35
V Note 6
fmax
Maximum Operation Frequency
2.5
2.5
Gb/s
1. 10SX circuits are designed to meet the AC specifications shown in the table after thermal equilibrium has been established. The circuit is mounted in a test socket
or mounted on a printed circuit board and transverse air greater than 500lfm is maintained.
2. The differential propagation delay is defined as the delay from the crossing points of the differential input signals to the crossing point of the differential output
signals.
3. The single-ended propagation delay is defined as the delay from the 50% point of the input signal to the 50% point of the output signal.
4. Duty cycle skew is the difference between tPLH and tPHL propagation delay through a device.
5. Minimum input swing for which AC parameters are guaranteed.
6. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range
and the peak-to-peak voltage lies between VPP Min and 1.0V.
7. Data taken at VCC, nom = 3.3V.
http://onsemi.com
3
Share Link: 