MC10EL89DTG データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
一致するリスト
MC10EL89DTG Datasheet PDF : 8 Pages
| |||
MC10EL89
Table 4. 10EL SERIES PECL DC CHARACTERISTICS VCC = 5.0 V; VEE = 0.0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 3)
Output LOW Voltage (Note 3)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 4)
23
28
23
28
23
28
mA
3.77 3.90 4.02 3.87 3.98 4.10 3.94 4.04 4.19 V
2.10 2.28 2.42 2.00 2.30 2.44 1.95 2.33 2.49 V
3770
4110 3870
4190 3940
4280 mV
3050
3500 3050
3520 3050
3555 mV
2.5
4.6 2.5
4.6 2.5
4.6
V
IIH
Input HIGH Current
70 150
50 150
40 150 mA
IIL
Input LOW Current
0.5 50
0.5 30
0.3 25
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.25 V / −0.5 V.
3. Outputs are terminated through a 50 W resistor to VCC − 3.0 V.
4. VIHCMR min varies 1:1 with VEE. VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
Table 5. 10EL SERIES NECL DC CHARACTERISTICS VCC = 0.0 V; VEE = −5.0 V (Note 5)
−40°C
25°C
85°C
Symbol
IEE
VOH
VOL
VIH
Characteristic
Power Supply Current
Output HIGH Voltage (Note 6)
Output LOW Voltage (Note 6)
Input HIGH Voltage (Single−Ended)
Min Typ Max Min Typ Max Min Typ Max Unit
23
28
23
28
23
28
mA
−1.23 −1.10 −0.98 −1.13 −1.02 −0.90 −1.06 −0.96 −0.81 V
−2.90 −2.72 −2.58 −3.00 −2.70 −2.56 −3.05 −2.67 −2.51 V
−123
0
−890 −1130
−810 −106
0
−720 mV
VIL
Input LOW Voltage (Single−Ended)
−195
0
−150 −195
0
0
−148 −195
0
0
−144 mV
5
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 7)
−2.5
−0.4 −2.5
−0.4 −2.5
−0.4 V
IIH
Input HIGH Current
70 150
50 150
20 150 mA
IIL
Input LOW Current
0.5 50
0.5 30
0.3 25
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. Input and output parameters vary 1:1 with VCC. VEE can vary +0.25 V / −0.5 V.
6. Outputs are terminated through a 50 W resistor to VCC − 3.0 V.
7. VIHCMR min varies 1:1 with VEE. VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
http://onsemi.com
3
Share Link: 