MAX3864 データシートの表示（PDF） - Maxim Integrated

部品番号

コンポーネント説明

一致するリスト

MAX3864

2.5Gbps, +3V to +5.5V, Wide Dynamic Range Transimpedance Preamplifier

Maxim Integrated 

2.5Gbps, +3V to +5.5V, Wide Dynamic Range

Transimpedance Preamplifier

ABSOLUTE MAXIMUM RATINGS

Supply Voltage (VCC - GND) .................................-0.5V to +6.0V

IN Current..............................................................-4mA to +4mA

FILTER Current......................................................-8mA to +8mA

Voltages at OUT+, OUT- .................(VCC - 1.5V) to (VCC + 0.5V)

Continuous Power Dissipation (TA = +85°C)

8-Pin SO package (derate 6.7mW/°C above +85°C) ..436mW

Storage Temperature Range .............................-55°C to +150°C

Operating Junction Temperature ......................-55°C to +150°C

Processing Temperature (die) .........................................+400°C

Lead Temperature (soldering, 10s) .................................+300°C

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

ELECTRICAL CHARACTERISTICS

(VCC = +3.0V to +5.5V, 100Ω load between OUT+ and OUT-, 0.1µF coupling capacitors on OUT+ and OUT-, TA = -40°C to +85°C,

unless otherwise noted. Typical values are at +3.3V, source capacitance = 0.85pF, and TA = +25°C.) (Note 1)

PARAMETER

Input Bias Voltage

Supply Current

Transimpedance

Output Impedance

Maximum Differential Output Voltage

Filter Resistor

AC Input Overload

DC Input Overload

Input-Referred RMS Noise

Input-Referred Noise Density

Small-Signal Bandwidth

Low-Frequency Cutoff

Transimpedance Linear Range

Deterministic Jitter

Power-Supply Rejection Ratio (PSRR)

CONDITIONS

Differential, measured with 40µAP-P input

Single ended (per side)

Input = 2mAP-P with 100Ω differential output

termination

Bandwidth = 2.0GHz (Note 2)

-3dB, input ≤ 20µADC

Gain at 40µAP-P is within 5% of the small-

signal gain

3.13V < VCC < 5.5V (Note 3)

3.0V ≤ VCC ≤ 3.13V (Note 3)

Output referred, f < 2MHz,

PSRR = -20log(ΔVOUT/ΔVCC)

MIN

0.66

2100

48

220

600

2

1

1525

40

TYP

0.83

34

2750

50

380

750

490

11

2000

30

24

24

50

MAX

0.99

63

3400

52

575

930

668

UNITS

V

mA

Ω

Ω

mVP-P

Ω

mAP-P

mA

nA

pA/√Hz

MHz

kHz

µAP-P

67

ps

77

dB

Note 1: Source capacitance represents the total capacitance at the IN pin during characterization of noise and bandwidth parame-

ters. Noise and bandwidth will be affected by the source capacitance. See the Typical Operating Characteristics for more

information.

Note 2: Input-referred noise is calculated as (RMS output noise) / (Gain at f = 10MHz). Noise density is (Input-Referred Noise) /

(Bandwidth)1/2. No external filters are used for the noise measurements.

Note 3: Deterministic jitter is defined as the arithmetic sum of pulse-width distortion and pattern dependent jitter measured with a

repeating 20-bit pattern of 00111110101100000101 (K28.5). See Typical Operating Characteristics.

2 _______________________________________________________________________________________

Share Link: