MAX1771 データシートの表示（PDF） - Maxim Integrated
部品番号
コンポーネント説明
一致するリスト
MAX1771 Datasheet PDF : 16 Pages
| |||
12V or Adjustable, High-Efficiency,
Low IQ, Step-Up DC-DC Controller
VIN = 5V
C3
0.1µF
C2
0.1µF
2
V+
5 REF
MAX1771
4 SHDN
L1
22µH
C1
68µF
D1
1N5817-22
3 FB
6 AGND
GND
7
1
EXT
8
CS
N
Si9410DY/
MTD20N03HDL
RSENSE
40mΩ
VOUT = 12V
@ 0.5A
C4
300µF
Figure 2a. 12V Preset Output, Bootstrapped
VIN = 5V
C1
68µF
C3
0.1µF
C2
0.1µF
2
V+
5 REF
4
MAX1771
SHDN
6 AGND
GND
7
( ) R2 = (R1) VOUT -1
VREF
VREF = 1.5V
L1
22µH
D1
1N5817-22
VOUT = 12V
@ 0.5A
1
EXT
8
CS
FB 3
C4
N
300µF
MTD20N03HDL
RSENSE
R2
40mΩ
127k
R1
18k
C5
100pF
Figure 2b. 12V Output, Non-Bootstrapped
VIN = 4V
C3
0.1µF
C2
0.1µF
2
V+
5 REF
4
MAX1771
SHDN
6
AGND
GND
7
( ) R2 = (R1) VOUT -1
VREF
VREF = 1.5V
L1
22µH
C1
47µF
D1
1N5817-22
VOUT = 9V
1
EXT
8
CS
3
FB
N
Si9410DY/
C4
200µF
MTD20N03HDL
RSENSE
R2
40mΩ
140k
R1
28k
C5
100pF
Figure 2c. 9V Output, Bootstrapped
increases at low input voltages. However, the supply
current is also reduced because V+ is at a lower volt-
age, and because less energy is consumed while
charging and discharging the external MOSFET’s gate
capacitance. The minimum input voltage is 3V when
using external feedback resistors. With supply voltages
below 5V, bootstrapped mode is recommended.
Note: When using the MAX1771 in non-boot-
strapped mode, there is no preset output operation
because V+ is also the output voltage sense point
for fixed-output operation. External resistors must
be used to set the output voltage. Use 1% external
feedback resistors when operating in adjustable-output
mode (Figures 2b, 2c) to achieve an overall output volt-
age accuracy of ±5%. To achieve highest efficiency,
operate in bootstrapped mode whenever possible.
External Power-Transistor
Control Circuitry
PFM Control Scheme
The MAX1771 uses a proprietary current-limited PFM
control scheme to provide high efficiency over a wide
range of load currents. This control scheme combines the
ultra-low supply current of PFM converters (or pulse skip-
pers) with the high full-load efficiency of PWM converters.
Unlike traditional PFM converters, the MAX1771 uses a
sense resistor to control the peak inductor current. The
device also operates with high switching frequencies
(up to 300kHz), allowing the use of miniature external
components.
As with traditional PFM converters, the power transistor
is not turned on until the voltage comparator senses
the output is out of regulation. However, unlike tradition-
al PFM converters, the MAX1771 switch uses the com-
bination of a peak current limit and a pair of one-shots
that set the maximum on-time (16µs) and minimum off-
time (2.3µs); there is no oscillator. Once off, the mini-
mum off-time one-shot holds the switch off for 2.3µs.
After this minimum time, the switch either 1) stays off if
the output is in regulation, or 2) turns on again if the
output is out of regulation.
8 _______________________________________________________________________________________
Share Link: 