LTC1405C データシートの表示（PDF） - Linear Technology

部品番号

コンポーネント説明

一致するリスト

LTC1405C

12-Bit, 5Msps, Sampling ADC

Linear Technology 

LTC1405

APPLICATIO S I FOR ATIO

Digital Outputs and Overflow Bit (OF)

Figure 10 shows the ideal input/output characteristics for

the LTC1405. The output data is two’s complement binary

for all input ranges and for both single and dual supply

operation. One LSB = VREF/4.096. To create a straight

binary output, invert the MSB (D11). The overflow bit (OF)

indicates when the analog input is outside the input range

of the converter. OF is high when the output code is 1000

0000 0000 or 0111 1111 1111.

1 OVERFLOW

0 BIT

011…111

011…110

011…101

noise from affecting performance, the load capacitance on

the digital outputs should be minimized. If large capacitive

loads are required, (>30pF) external buffers or 100Ω

resistors in series with the digital outputs are suggested.

5V

5V

R1

50k

–5V

VIN

24k

100Ω

1µF

10k

R2

1k

10k

+AIN

LTC1405

–AIN

VREF

SENSE

VSS

1405 F11

–5V

100…010

100…001

100…000

–(FS – 1LSB)

INPUT VOLTAGE (V)

FS – 1LSB

1405 F10

Figure 10. LTC1405 Transfer Characteristics

Full-Scale and Offset Adjustment

In applications where absolute accuracy is important,

offset and full-scale errors can be adjusted to zero. Offset

error should be adjusted before full-scale error. Figure 11

shows a method for error adjustment for a dual supply,

4.096V application. For zero offset error apply – 0.5mV

(i. e., – 0.5LSB) at + AIN and adjust R1 until the output code

flickers between 0000 0000 0000 and 1111 1111 1111.

For full-scale adjustment, apply an input voltage of 2.0465V

(FS – 1.5LSBs) at + AIN and adjust R2 until the output code

flickers between 0111 1111 1110 and 0111 1111 1111.

Digital Output Drivers

The LTC1405 output drivers can interface to logic operat-

ing from 3V to 5V by setting OVDD to the logic power

supply. If 5V output is desired, OVDD can be shorted to VDD

and share its decoupling capacitor. Otherwise, OVDD re-

quires its own 1µF decoupling capacitor. To prevent digital

Figure 11. Offset and Full-Scale Adjust Circuit

Timing

The conversion start is controlled by the rising edge of the

CLK pin. Once a conversion is started it cannot be stopped

or restarted until the conversion cycle is complete. Output

data is updated at the end of conversion, or about 150ns

after a conversion is begun. There is an additional two

cycle pipeline delay, so the data for a given conversion is

output two full clock cycles plus 150ns after the convert

start. Thus output data can be latched on the third CLK

rising edge after the rising edge that samples the input.

Clock Input

The LTC1405 only uses the rising edge of the CLK pin for

internal timing, and CLK doesn’t necessarily need to have

a 50% duty cycle. For optimal AC performance the rise

time of the CLK should be less than 5ns. If the available

clock has a rise time slower than 5ns, it can be locally sped

up with a logic gate. With single supply operation the clock

can be driven with 5V CMOS, 3V CMOS or TTL logic levels.

With dual power supplies the clock should be driven with

5V CMOS levels.

As with all fast ADCs, the noise performance of the

LTC1405 is sensitive to clock jitter when high speed inputs

11

Share Link: