HIP4081A データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
一致するリスト
HIP4081A Datasheet PDF : 17 Pages
| |||
HIP4081A
Absolute Maximum Ratings
Thermal Information
Supply Voltage, VDD and VCC . . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V
Voltage on AHS, BHS . . . -6.0V (Transient) to 80V (25°C to 125°C)
Voltage on AHS, BHS . . . -6.0V (Transient) to 70V (-55°C to 125°C)
Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient)
Voltage on AHB, BHB . . . . . . . . VAHS, BHS -0.3V to VAHS, BHS +VDD
Voltage on ALO, BLO. . . . . . . . . . . . . .VALS, BLS -0.3V to VCC +0.3V
Voltage on AHO, BHO . . . . . . . .VAHS, BHS -0.3V to VAHB, BHB +0.3V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
NOTE: All Voltages relative to VSS, unless otherwise specified.
Operating Conditions
Supply Voltage, VDD and VCC . . . . . . . . . . . . . . . . . . +9.5V to +15V
Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V
Voltage on AHB, BHB . . . . . . . . . VAHS, BHS +5V to VAHS, BHS +15V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . .-500A to -50A
Operating Ambient Temperature Range . . . . . . . . . . .-40°C to 85°C
Thermal Resistance (Typical, Note 1)
JA (°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
85
DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
Storage Temperature Range . . . . . . . . . . . . . . . . . . . -65°C to 150°C
Operating Max. Junction Temperature. . . . . . . . . . . . . . . . . . . 125°C
Lead Temperature (Soldering 10s)) . . . . . . . . . . . . . . . . . . . . . 300°C
(For SOIC - Lead Tips Only
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
PARAMETER
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100K and
TA = 25°C, Unless Otherwise Specified
TJ = 25°C
TJS = -40°C TO
125°C
SYMBOL
TEST CONDITIONS
MIN TYP MAX MIN MAX UNITS
SUPPLY CURRENTS AND CHARGE PUMPS
VDD Quiescent Current
VDD Operating Current
VCC Quiescent Current
VCC Operating Current
AHB, BHB Quiescent Current -
Qpump Output Current
IDD
IDDO
ICC
ICCO
IAHB, IBHB
AHB, BHB Operating Current
AHS, BHS, AHB, BHB Leakage
Current
IAHBO, IBHBO
IHLK
AHB-AHS, BHB-BHS Qpump
Output Voltage
VAHB-VAHS
VBHB-VBHS
INPUT PINS: ALI, BLI, AHI, BHI, AND DIS
All inputs = 0V
Outputs switching f = 500kHz
All Inputs = 0V, IALO = IBLO = 0
f = 500kHz, No Load
All Inputs = 0V, IAHO = IBHO = 0
VDD = VCC = VAHB = VBHB = 10V
f = 500kHz, No Load
VBHS = VAHS = 80V,
VAHB = VBHB = 93V
IAHB = IAHB = 0, No Load
8.5 10.5 14.5 7.5 14.5
mA
9.5 12.5 15.5 8.5 15.5
mA
-
0.1
10
-
20
A
1
1.25 2.0
0.8
3
mA
-50 -30 -11 -60 -10
A
0.6
1.2
1.5
0.5
1.9
mA
-
0.02 1.0
-
10
A
11.5 12.6 14.0 10.5 14.5
V
Low Level Input Voltage
High Level Input Voltage
Input Voltage Hysteresis
VIL
Full Operating Conditions
VIH
Full Operating Conditions
-
-
1.0
-
0.8
V
2.5
-
-
2.7
-
V
-
35
-
-
-
mV
Low Level Input Current
IIL
High Level Input Current
IIH
TURN-ON DELAY PINS: LDEL AND HDEL
VIN = 0V, Full Operating Conditions
-130 -100 -75 -135 -65
A
VIN = 5V, Full Operating Conditions
-1
-
+1
-10 +10
A
LDEL, HDEL Voltage
VHDEL, VLDEL IHDEL = ILDEL = -100A
GATE DRIVER OUTPUT PINS: ALO, BLO, AHO, AND BHO
4.9
5.1
5.3
4.8
5.4
V
Low Level Output Voltage
High Level Output Voltage
Peak Pullup Current
VOL
VCC-VOH
IO+
IOUT = 100mA
IOUT = -100mA
VOUT = 0V
0.7 0.85 1.0
0.5
1.1
V
0.8 0.95 1.1
0.5
1.2
V
1.7
2.6
3.8
1.4
4.1
A
4
Share Link: 