M27V401 データシートの表示（PDF） - STMicroelectronics
部品番号
コンポーネント説明
一致するリスト
M27V401 Datasheet PDF : 16 Pages
| |||
M27V401
Table 9. Programming Mode DC Characteristics (1)
(TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12.75V ± 0.25V)
Symbol
Parameter
Test Condition
Min
Max
ILI
Input Leakage Current
VIL ≤ VIN ≤ VIH
±10
ICC
Supply Current
50
IPP
Program Current
E = VIL
50
VIL
Input Low Voltage
–0.3
0.8
VIH
Input High Voltage
2
VCC + 0.5
VOL
Output Low Voltage
IOL = 2.1mA
0.4
VOH
Output High Voltage TTL
IOH = –400µA
2.4
VID
A9 Voltage
11.5
12.5
Note: 1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
Unit
µA
mA
mA
V
V
V
V
V
Table 10. Programming Mode AC Characteristics (1)
(TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12.75V ± 0.25V)
Symbol
Alt
Parameter
Test Condition
Min
tAVPL
tAS Address Valid to Program Low
2
tQVPL
tDS Input Valid to Program Low
2
tVPHPL
tVPS VPP High to Program Low
2
tVCHPL
tVCS VCC High to Program Low
2
tELPL
tCES Chip Enable Low to Program Low
2
tPLPH
tPW Program Pulse Width
95
tPHQX
tDH Program High to Input Transition
2
tQXGL
tOES Input Transition to Output Enable Low
2
tGLQV
tOE Output Enable Low to Output Valid
tGHQZ (2)
tDFP Output Enable High to Output Hi-Z
0
tGHAX
tAH
Output Enable High to Address
Transition
0
Note: 1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
2. Sampled only, not 100% tested.
Max Unit
µs
µs
µs
µs
µs
105
µs
µs
µs
100
ns
130
ns
ns
Programming
The M27V401 has been designed to be fully com-
patible with the M27C4001 and has the same elec-
tronic signature. As a result the M27V401 can be
programmed as the M27C4001 on the same pro-
gramming equipments applying 12.75V on VPP
and 6.25V on VCC by the use of the same PRES-
TO II algorithm. When delivered (and after each
erasure for UV EPROM), all bits of the M27V401
are in the ’1’ state. Data is introduced by selective-
ly programming ’0’s into the desired bit locations.
Although only ’0’s will be programmed, both ’1’s
and ’0’s can be present in the data word. The only
way to change a ’0’ to a ’1’ is by die exposure to ul-
traviolet light (UV EPROM). The M27V401 is in the
programming mode when VPP input is at 12.75V,
G at VIH and E is pulsed to VIL. The data to be pro-
grammed is applied to 8 bits in parallel to the data
output pins. The levels required for the address
and data inputs are TTL. VCC is specified to be
6.25V ± 0.25V.
7/15
Share Link: 