AAT3166 データシートの表示（PDF） - Analog Technology Inc
部品番号
コンポーネント説明
一致するリスト
AAT3166 Datasheet PDF : 14 Pages
| |||
AAT3166
High Efficiency 1X/1.5X/2X Charge
Pump for White LED Applications
brightness appears linear with each increasing
code count. Because the inputs D1 to D4 are true
independent constant current sinks, the voltage
observed on any single given input will be deter-
mined by the actual forward voltage (VF) for the
LED being driven.
Since the input current sinks of the AAT3166 are
programmable, no PWM (pulse width modulation) or
additional control circuitry is needed to control LED
brightness. This feature greatly reduces the burden
on a microcontroller or system IC to manage LED or
display brightness, allowing the user to "set it and
forget it." With its high-speed serial interface (1MHz
data rate), the input sink current of the AAT3166 can
be changed successively to brighten or dim LEDs in
smooth transitions (e.g., to fade-out) or in abrupt
steps, giving the user complete programmability and
real-time control of LED brightness.
The 16 individual current level settings are each
approximately 1.8dB apart (see Table 1). Code 1 is
full scale; Code 15 is full scale attenuated by
approximately 25dB; and Code 16 is reserved as a
"no current" setting.
Data
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
27mA Max
IOUT (mA)
27
22
18
14
12
10
8
6.2
5.2
4.3
3.3
2.9
2.4
1.9
1.4
0
18mA Max
IOUT (mA)
18
15
12
10
7.9
6.3
5.1
4.1
3.5
2.9
2.2
1.9
1.6
1.3
1.0
0
14mA Max
IOUT (mA)
14
11
8.8
7.1
6.0
4.8
3.8
3.1
2.6
2.1
1.7
1.4
1.2
1.0
0.7
0
Table 1: Current Level Settings.
AS2Cwire Serial Interface
The current sink input magnitude of the AAT3166 is
controlled by AnalogicTech's Advanced Simple
Serial Control (AS2Cwire) serial digital input.
AS2Cwire adds addressing capability for multiple
data registers over the Simple Serial Control™
(S2Cwire™), which is capable of controlling only a
single register. The AAT3166 has four registers:
Bank1, Bank2, Max Current, and Low Current.
Three addresses are used to control the two regis-
ters. Address 0 addresses both registers simultane-
ously to allow the loading of both registers with the
same data using a single write protocol. Address 1
addresses Register 1 for D1 to D3 current level set-
tings. Address 2 addresses Register 2 for D4 cur-
rent level settings.
AS2Cwire relies on the number of rising edges of
the EN/SET pin to address and load the registers.
AS2Cwire latches data or address after the EN/SET
pin has been held high for time TLAT. Address or
data is differentiated by the number of EN/SET ris-
ing edges. Since the data registers are 4 bits each,
the differentiating number of pulses is 24 or 16, so
that Address 0 is signified by 17 rising edges,
Address 1 by 18 rising edges, and Address 2 by 19
rising edges. Data is set to any number of rising
edges between 1 and including 16. A typical write
protocol is a burst of EN/SET rising edges signify-
ing a particular address, followed by a pause with
EN/SET held high for the TLAT timeout period, a
burst of rising edges signifying data, and a TLAT
timeout for the data registers. Once an address is
set, then multiple writes consisting of data only
(without address) to the corresponding data regis-
ter are allowed. Address 0 is the default address
on the first rising edge after the AAT3166 has been
disabled. If data is presented on the first rising
edge with no prior address, both data registers are
simultaneously loaded.
The maximum current level is determined by the
value set in Register 3, the Max Current register.
Three scales are available for high operating cur-
rents with maximum current levels of 27mA, 18mA,
or 14mA. Each scale maintains approximately
1.8dB steps between settings. A separate mode is
3166.2006.05.1.2
9
Share Link: 