AT52BR1674T-85CI データシートの表示（PDF） - Atmel Corporation

部品番号

コンポーネント説明

一致するリスト

AT52BR1674T-85CI

16-megabit Flash and 2-megabit/ 4-megabit SRAM Stack Memory

Atmel Corporation 

Device

Operation

READ: The 16-megabit Flash is accessed like an EPROM. When CE and OE are low and WE

is high, the data stored at the memory location determined by the address pins are asserted

on the outputs. The outputs are put in the high-impedance state whenever CE or OE is high.

This dual-line control gives designers flexibility in preventing bus contention.

COMMAND SEQUENCES: When the device is first powered on it will be reset to the read or

standby mode, depending upon the state of the control line inputs. In order to perform other

device functions, a series of command sequences are entered into the device. The command

sequences are shown in the Command Definitions table (I/O8 - I/O15 are don’t care inputs for

the command codes). The command sequences are written by applying a low pulse on the

WE or CE input with CE or WE low (respectively) and OE high. The address is latched on the

falling edge of CE or WE, whichever occurs last. The data is latched by the first rising edge of

CE or WE. Standard microprocessor write timings are used. The address locations used in the

command sequences are not affected by entering the command sequences.

RESET: A RESET input pin is provided to ease some system applications. When RESET is at

a logic high level, the device is in its standard operating mode. A low level on the RESET input

halts the present device operation and puts the outputs of the device in a high-impedance

state. When a high level is reasserted on the RESET pin, the device returns to the read or

standby mode, depending upon the state of the control inputs.

ERASURE: Before a word can be reprogrammed, it must be erased. The erased state of

memory bits is a logical “1”. The entire device can be erased by using the Chip Erase com-

mand or individual sectors can be erased by using the Sector Erase command.

CHIP ERASE: The entire device can be erased at one time by using the six-byte chip erase

software code. After the chip erase has been initiated, the device will internally time the erase

operation so that no external clocks are required. The maximum time to erase the chip is tEC.

If the sector lockdown has been enabled, the chip erase will not erase the data in the sector

that has been locked out; it will erase only the unprotected sectors. After the chip erase, the

device will return to the read or standby mode.

SECTOR ERASE: As an alternative to a full chip erase, the device is organized into 39 sec-

tors (SA0 - SA38) that can be individually erased. The Sector Erase command is a six-bus

cycle operation. The sector address is latched on the falling WE edge of the sixth cycle while

the 30H data input command is latched on the rising edge of WE. The sector erase starts after

the rising edge of WE of the sixth cycle. The erase operation is internally controlled; it will

automatically time to completion. The maximum time to erase a section is tSEC. When the sec-

tor programming lockdown feature is not enabled, the sector will erase (from the same Sector

Erase command). An attempt to erase a sector that has been protected will result in the oper-

ation terminating in 2 µs.

WORD PROGRAMMING: Once a memory block is erased, it is programmed (to a logical “0”)

on a word-by-word basis. Programming is accomplished via the internal device command reg-

ister and is a four-bus cycle operation. The device will automatically generate the required

internal program pulses.

Any commands written to the chip during the embedded programming cycle will be ignored. If

a hardware reset happens during programming, the data at the location being programmed

will be corrupted. Please note that a data “0” cannot be programmed back to a “1”; only erase

operations can convert “0”s to “1”s. Programming is completed after the specified tBP cycle

time. The Data Polling feature or the Toggle Bit feature may be used to indicate the end of a

program cycle.

VPP PIN: The circuitry of the 16-megabit Flash is designed so that the device can be pro-

grammed or erased from the VCC power supply or from the VPP input pin. When VPP is less

than or equal to the VCC pin, the device selects the VCC supply for programming and erase

6 AT52BR1672(T)/1674(T)

2604B–STKD–09/02

Share Link: