PEEL22CV10 データシートの表示（PDF） - Unspecified
部品番号
コンポーネント説明
一致するリスト
PEEL22CV10
Unspecified
PEEL22CV10 Datasheet PDF : 10 Pages
| |||
PEELTM 22CV10A
Table 9. A.C. Electrical Characteristics Over the Operating Range8,11
Symbol Parameter
tPD
Input5 to non-registered output
tOE
Input5 to output enable6
tOD
Input5 to output disable6
tCO1
tCO2
Clock to Output
Clock to comb. output delay via
internal registered feedback
tCF
tSC
tHC
tCL, tCH
tCP
Clock to Feedback
Input5 or Feedback Setup to Clock
Input5 Hold After Clock
Clock Low Time, Click High Time8
Min Clock Period Ext (tSC + tCO1)
fMAX1
Internal Feedback (1tSC + tCF)12
fMAX2
fMAX3
tAW
tAP
tAR
tRESET
External Feedback (1/tCP)12
No Feedback (1/tCL + tCH)12
Asynchronous Reset Pulse Width
Input5 to Asynchronous Reset
Asynch. Reset recovery time
Power-on Reset Time for
registers in Clear State
Switching Waveforms
Inputs, I/O,
Registered Feedback,
Synchronous Preset
-7 / I-7
Min Max
7.5
7.5
7.5
5.5
10
3.5
3
0
3
8.5
142
117
166
7.5
7.5
7.5
5
-10 / I-10
Min Max
10
10
10
6
12
4
5
0
4
11
111
90.9
125
10
10
10
5
-15 / I-15
Min Max
15
15
15
8
17
5
8
0
6
18
76.9
62.5
83.3
15
15
15
5
-25 / I-25
Min Max
25
25
25
15
35
9
15
0
13
30
41.6
33.3
38.4
25
25
25
5
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
MHz
MHz
MHz
ns
ns
ns
µs
Clock
Asynchronous
Reset
Registered
Outputs
Combinatorial
Outputs
Notes
1. Minimum DC input is -0.5V, however inputs may undershoot to -2.0V for
periods less than 20ns.
2. VI and VO are not specified for program/verify operation.
3. Test points for Clock and VCC in tR, tF are referenced at 10% and 90%
levels.
4. I/O pins are 0V and 3V.
5. “Input” refers to an Input pin signal.
6. tOE is measured from input transition to VREF ± 0.1V, tOD is measured
from input transition to VOH -0.1V or VOL +0.1V; VREF =VL see test loads
in Section 5 of the Data Book.
7. Capacitances are tested on a sample basis.
8. Test conditions assume: signal transition times of 3ns or less from the
10% and 90% points, timing reference levels of 1.5V (unless otherwise
specified).
9. Test one output at a time for a duration of less than 1sec.
10. ICC for a typical application: This parameter is tested with the device
programmed as an 8-bit Counter.
11. PEEL™ Device test loads are specified in Section 6 of this Data Book.
12. Parameters are not 100% tested. Specifications are based on initial
characterization and are tested after any design or process modifica-
tion which may affect operational frequency.
13. Available only for 22CV10A -15/I-15/-25/I-25 grades.
8 of 10
04-02-009F
Share Link: