TESVSP0A225M8L データシートの表示（PDF） - NEC => Renesas Technology
部品番号
コンポーネント説明
一致するリスト
TESVSP0A225M8L Datasheet PDF : 16 Pages
| |||
SVS SERIES
SPECIFICATIONS
No.
Items
1 Operating Temp. Range
2 Rated Voltage
3 Surge Voltage
4 Derated Voltage
5 Capacitance Range
6 Capacitance Tolerance
7 Leakage Current
8 Tangent of loss angle
9 Surge Voltage Resistance
Characteris-
tics at high
10
and low
temperature
Temp.
∆C/C
Tangent of
loss angle
Leakage
Current
11 Rapid change of temperature
12 Resistance to soldering
13 Damp Heat (Steady state)
14 Endurance
15 Failure Rate
Specifications
Test Conditions
–55 to +125˚C
Over 85˚C, applied voltage shall be derated
on the basis of the Derated Voltage at
125˚C specified in this table item no.4.
2.5
4
6.3
10
16
Vdc
3.3
5.2
8
13
20
Vdc
1.6
2.5
4
6.3
10
Vdc
0.33 to 10 µF
± 20%
0.5 µA max.
0.1 max. / 0.2 max. (Refer to ratings)
∆C/C
: ±20%
Tangent of loss angle : Initial requirement
Leakage Current
: Initial requirement
–55˚C
0
– 20
%
150% of initial
requirement
+85˚C
+20
0
%
Initial
requirement
+125˚C
+20
0
%
150%of initial
requirement
0.1 CV or 5 µA 0.125 CV or 6.25 µA
––
whichever is whichever is
greater
greater
up to 85˚C
up to 85˚C
at 125˚C
at 120 Hz
at 120 Hz
5 min. after rated voltage applied
at 25˚C, 120 Hz
at 85˚C
Surge voltage for 30 sec. (Rs = 1 kΩ)
Discharge for 5 min. 30 sec.
1 000 cycles
Step1 : +25˚C
Step2 : –55˚C
Step3 : +25˚C
Step4 : +85˚C
Step5 : +125˚C
Step6 : +25˚C
∆C/C
: ±20%
Tangent of loss angle : Initial requirement
Leakage Current
: Initial requirement
∆C/C
: ±20%
Tangent of loss angle : Initial requirement
Leakage Current
: Initial requirement
IEC68-2-14 Test N and IEC68-2-33
Guidance
–55 to +125˚C
5 cycles
IEC68-2-58 Test Td
Fully immersion to solder at 260˚C for
5 sec
∆C/C
: ±20%
Tangent of loss angle : 150% of Intial requirement
Leakage Current
: Initial requirement
IEC68-2-3 Test Ca
at 40˚C, 90 to 95% RH, for 500H
∆C/C
: ±20%
Tangent of loss angle : Initial requirement
Leakage Current
: 200% of Initial requirement
at 85˚C & 125˚C (Derated Voltage),
rated voltage applied for 2 000 H
λ0 = 1% / 1 000 h
at 85˚C & 125˚C (Derated Voltage),
rated voltage applied for 1 000 H
∆ C /C : Capacitance change ratio
4
Share Link: 